Skip to contentSkip to conversation

model needed for Clevo P150HM (Realtek ALC892)

DISCUSSION Julian Sikorski 3 participants 68 messages Jun 23, 2011 – Jul 18, 2011 1 message not in the archive Sound

lore
Share & tools
lore
#0 lore raw

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

Regards,
Julian

[1] http://thread.gmane.org/gmane.comp.audio.pulseaudio.general/10096
[2]
http://www.alsa-project.org/db/?f=7c91e874f4272387c2c51e448337567202c0edfe

#1 lore raw

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +16 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
 	hda_nid_t dac;
 
 	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
 	for (i = 0; i < cfg->line_outs; i++) {
 		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
 		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
 	unsigned int location, defcfg;
 	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT && cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
 	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
 		return 0;
 
 	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
 		spec->multi_ios = num_pins;
 		spec->ext_channel_count = 2;
 		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
 	}
 	return 0;
 }
#2 lore raw
Quoted 61 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
  	hda_nid_t dac;
 
  	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
  	for (i = 0; i<  cfg->line_outs; i++) {
  		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
  		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
  	unsigned int location, defcfg;
  	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&  cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
  	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
  		return 0;
 
  	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 8 lines
sound/pci/hda/patch_realtek.c +2 -0
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
  		spec->multi_ios = num_pins;
  		spec->ext_channel_count = 2;
  		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
  	}
  	return 0;
  }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Julian

#3 lore raw

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
  	hda_nid_t dac;
 
  	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
  	for (i = 0; i<  cfg->line_outs; i++) {
  		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
  		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
  	unsigned int location, defcfg;
  	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&  cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
  	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
  		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
  	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
  		spec->multi_ios = num_pins;
  		spec->ext_channel_count = 2;
  		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
  	}
  	return 0;
  }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

thanks,

Takashi

#4 lore raw

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
  	hda_nid_t dac;
 
  	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
  	for (i = 0; i<  cfg->line_outs; i++) {
  		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
  		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
  	unsigned int location, defcfg;
  	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&  cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
  	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
  		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
  	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
  		spec->multi_ios = num_pins;
  		spec->ext_channel_count = 2;
  		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
  	}
  	return 0;
  }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Takashi

---
Subject: [PATCH] ALSA: hda - Clean up multi-channel mixer name assignment in
patch_realtek.c

Change alc_get_line_out_pfx() in patch_realtek.c to provide the channel specific name and assign the index so that each caller doesn't have to set the channel name by itself.

Also, check the multi-io case with the primary hp-out; for the multi-io channels, assign the channel name instead of "Headphone" with indices. This makes the mixer names more intuitive and reduces confusion.

---
 sound/pci/hda/patch_realtek.c |   92 ++++++++++++++++-------------------------
 1 files changed, 36 insertions(+), 56 deletions(-)
sound/pci/hda/patch_realtek.c +36 -56
index b0cf726..7858da5 100644
@@ -5359,11 +5359,15 @@ static int alc880_auto_fill_dac_nids(struct alc_spec *spec,
 	return 0;
 }
 
-static const char *alc_get_line_out_pfx(struct alc_spec *spec,
-					bool can_be_master)
+static const char *alc_get_line_out_pfx(struct alc_spec *spec, int ch,
+					bool can_be_master, int *index)
 {
 	struct auto_pin_cfg *cfg = &spec->autocfg;
+	static const char * const chname[4] = {
+		"Front", "Surround", NULL /*CLFE*/, "Side"
+	};
 
+	*index = 0;
 	if (cfg->line_outs == 1 && !spec->multi_ios &&
 	    !cfg->hp_outs && !cfg->speaker_outs && can_be_master)
 		return "Master";
@@ -5374,23 +5378,23 @@ static const char *alc_get_line_out_pfx(struct alc_spec *spec,
 			return "Speaker";
 		break;
 	case AUTO_PIN_HP_OUT:
+		/* for multi-io case, only the primary out */
+		if (ch && spec->multi_ios)
+			break;
+		*index = ch;
 		return "Headphone";
 	default:
 		if (cfg->line_outs == 1 && !spec->multi_ios)
 			return "PCM";
 		break;
 	}
-	return NULL;
+	return chname[ch];
 }
 
 /* add playback controls from the parsed DAC table */
 static int alc880_auto_create_multi_out_ctls(struct alc_spec *spec,
 					     const struct auto_pin_cfg *cfg)
 {
-	static const char * const chname[4] = {
-		"Front", "Surround", NULL /*CLFE*/, "Side"
-	};
-	const char *pfx = alc_get_line_out_pfx(spec, false);
 	hda_nid_t nid;
 	int i, err, noutputs;
 
@@ -5399,10 +5403,13 @@ static int alc880_auto_create_multi_out_ctls(struct alc_spec *spec,
 		noutputs += spec->multi_ios;
 
 	for (i = 0; i < noutputs; i++) {
+		const char *name;
+		int index;
 		if (!spec->multiout.dac_nids[i])
 			continue;
 		nid = alc880_idx_to_mixer(alc880_dac_to_idx(spec->multiout.dac_nids[i]));
-		if (!pfx && i == 2) {
+		name = alc_get_line_out_pfx(spec, i, false, &index);
+		if (!name) {
 			/* Center/LFE */
 			err = add_pb_vol_ctrl(spec, ALC_CTL_WIDGET_VOL,
 					      "Center",
@@ -5429,12 +5436,6 @@ static int alc880_auto_create_multi_out_ctls(struct alc_spec *spec,
 			if (err < 0)
 				return err;
 		} else {
-			const char *name = pfx;
-			int index = i;
-			if (!name) {
-				name = chname[i];
-				index = 0;
-			}
 			err = __add_pb_vol_ctrl(spec, ALC_CTL_WIDGET_VOL,
 						name, index,
 					  HDA_COMPOSE_AMP_VAL(nid, 3, 0,
@@ -12257,17 +12258,18 @@ static int alc262_auto_create_multi_out_ctls(struct alc_spec *spec,
 {
 	const char *pfx;
 	int vbits;
-	int i, err;
+	int i, index, err;
 
 	spec->multiout.num_dacs = 1;	/* only use one dac */
 	spec->multiout.dac_nids = spec->private_dac_nids;
 	spec->private_dac_nids[0] = 2;
 
-	pfx = alc_get_line_out_pfx(spec, true);
-	if (!pfx)
-		pfx = "Front";
 	for (i = 0; i < 2; i++) {
-		err = alc262_add_out_sw_ctl(spec, cfg->line_out_pins[i], pfx, i);
+		pfx = alc_get_line_out_pfx(spec, i, true, &index);
+		if (!pfx)
+			pfx = "PCM";
+		err = alc262_add_out_sw_ctl(spec, cfg->line_out_pins[i], pfx,
+					    index);
 		if (err < 0)
 			return err;
 		if (cfg->line_out_type != AUTO_PIN_SPEAKER_OUT) {
@@ -12287,10 +12289,11 @@ static int alc262_auto_create_multi_out_ctls(struct alc_spec *spec,
 	vbits = alc262_check_volbit(cfg->line_out_pins[0]) |
 		alc262_check_volbit(cfg->speaker_pins[0]) |
 		alc262_check_volbit(cfg->hp_pins[0]);
-	if (vbits == 1 || vbits == 2)
-		pfx = "Master"; /* only one mixer is used */
 	vbits = 0;
 	for (i = 0; i < 2; i++) {
+		pfx = alc_get_line_out_pfx(spec, i, true, &index);
+		if (!pfx)
+			pfx = "PCM";
 		err = alc262_add_out_vol_ctl(spec, cfg->line_out_pins[i], pfx,
 					     &vbits, i);
 		if (err < 0)
@@ -16035,10 +16038,6 @@ static int alc861_auto_create_multi_out_ctls(struct hda_codec *codec,
 					     const struct auto_pin_cfg *cfg)
 {
 	struct alc_spec *spec = codec->spec;
-	static const char * const chname[4] = {
-		"Front", "Surround", NULL /*CLFE*/, "Side"
-	};
-	const char *pfx = alc_get_line_out_pfx(spec, true);
 	hda_nid_t nid;
 	int i, err, noutputs;
 
@@ -16047,10 +16046,13 @@ static int alc861_auto_create_multi_out_ctls(struct hda_codec *codec,
 		noutputs += spec->multi_ios;
 
 	for (i = 0; i < noutputs; i++) {
+		const char *name;
+		int index;
 		nid = spec->multiout.dac_nids[i];
 		if (!nid)
 			continue;
-		if (!pfx && i == 2) {
+		name = alc_get_line_out_pfx(spec, i, true, &index);
+		if (!name) {
 			/* Center/LFE */
 			err = alc861_create_out_sw(codec, "Center", nid, 1);
 			if (err < 0)
@@ -16059,12 +16061,6 @@ static int alc861_auto_create_multi_out_ctls(struct hda_codec *codec,
 			if (err < 0)
 				return err;
 		} else {
-			const char *name = pfx;
-			int index = i;
-			if (!name) {
-				name = chname[i];
-				index = 0;
-			}
 			err = __alc861_create_out_sw(codec, name, nid, index, 3);
 			if (err < 0)
 				return err;
@@ -17178,10 +17174,6 @@ static void alc861vd_auto_init_analog_input(struct hda_codec *codec)
 static int alc861vd_auto_create_multi_out_ctls(struct alc_spec *spec,
 					     const struct auto_pin_cfg *cfg)
 {
-	static const char * const chname[4] = {
-		"Front", "Surround", "CLFE", "Side"
-	};
-	const char *pfx = alc_get_line_out_pfx(spec, true);
 	hda_nid_t nid_v, nid_s;
 	int i, err, noutputs;
 
@@ -17190,6 +17182,8 @@ static int alc861vd_auto_create_multi_out_ctls(struct alc_spec *spec,
 		noutputs += spec->multi_ios;
 
 	for (i = 0; i < noutputs; i++) {
+		const char *name;
+		int index;
 		if (!spec->multiout.dac_nids[i])
 			continue;
 		nid_v = alc861vd_idx_to_mixer_vol(
@@ -17199,7 +17193,8 @@ static int alc861vd_auto_create_multi_out_ctls(struct alc_spec *spec,
 				alc880_dac_to_idx(
 					spec->multiout.dac_nids[i]));
 
-		if (!pfx && i == 2) {
+		name = alc_get_line_out_pfx(spec, i, true, &index);
+		if (!name) {
 			/* Center/LFE */
 			err = add_pb_vol_ctrl(spec, ALC_CTL_WIDGET_VOL,
 					      "Center",
@@ -17226,12 +17221,6 @@ static int alc861vd_auto_create_multi_out_ctls(struct alc_spec *spec,
 			if (err < 0)
 				return err;
 		} else {
-			const char *name = pfx;
-			int index = i;
-			if (!name) {
-				name = chname[i];
-				index = 0;
-			}
 			err = __add_pb_vol_ctrl(spec, ALC_CTL_WIDGET_VOL,
 						name, index,
 					  HDA_COMPOSE_AMP_VAL(nid_v, 3, 0,
@@ -19030,10 +19019,6 @@ static int alc662_auto_create_multi_out_ctls(struct hda_codec *codec,
 					     const struct auto_pin_cfg *cfg)
 {
 	struct alc_spec *spec = codec->spec;
-	static const char * const chname[4] = {
-		"Front", "Surround", NULL /*CLFE*/, "Side"
-	};
-	const char *pfx = alc_get_line_out_pfx(spec, true);
 	hda_nid_t nid, mix, pin;
 	int i, err, noutputs;
 
@@ -19042,6 +19027,8 @@ static int alc662_auto_create_multi_out_ctls(struct hda_codec *codec,
 		noutputs += spec->multi_ios;
 
 	for (i = 0; i < noutputs; i++) {
+		const char *name;
+		int index;
 		nid = spec->multiout.dac_nids[i];
 		if (!nid)
 			continue;
@@ -19052,7 +19039,8 @@ static int alc662_auto_create_multi_out_ctls(struct hda_codec *codec,
 		mix = alc_auto_dac_to_mix(codec, pin, nid);
 		if (!mix)
 			continue;
-		if (!pfx && i == 2) {
+		name = alc_get_line_out_pfx(spec, i, true, &index);
+		if (!name) {
 			/* Center/LFE */
 			err = alc662_add_vol_ctl(spec, "Center", nid, 1);
 			if (err < 0)
@@ -19067,12 +19055,6 @@ static int alc662_auto_create_multi_out_ctls(struct hda_codec *codec,
 			if (err < 0)
 				return err;
 		} else {
-			const char *name = pfx;
-			int index = i;
-			if (!name) {
-				name = chname[i];
-				index = 0;
-			}
 			err = __alc662_add_vol_ctl(spec, name, nid, index, 3);
 			if (err < 0)
 				return err;
@@ -19361,8 +19343,6 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
 		spec->multi_ios = num_pins;
 		spec->ext_channel_count = 2;
 		spec->multiout.num_dacs = num_pins + 1;
-		/* for avoiding multi HP mixers */
-		cfg->line_out_type = AUTO_PIN_LINE_OUT;
 	}
 	return 0;
 }
Signature · 1 line
1.7.5.4
#5 lore raw
Quoted 85 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Quoted 7 lines

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.
How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Julian

#6 lore raw

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

#7 lore raw

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 94 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 7 lines
Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

I will definitely try.

Quoted 6 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

From my 1st mail:

It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out

Sorry if I wasn't clear, but the spdif out is a jack/optical hybrid.

Quoted 1 line

Takashi

Julian

#8 lore raw
In reply to Takashi Iwai

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

#9 lore raw

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Julian

Simple mixer control 'Master',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Headphone',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Speaker',0
Capabilities: pswitch penum
Playback channels: Front Left - Front Right
Mono:
Front Left: Playback [on]
Front Right: Playback [on]
Simple mixer control 'PCM',0
Capabilities: pvolume penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 255 [100%] [0.00dB]
Front Right: Playback 255 [100%] [0.00dB]
Simple mixer control 'Surround',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Center',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'LFE',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Line',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 3 [100%] [30.00dB]
Front Right: 3 [100%] [30.00dB]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958 Default PCM',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 46 [100%] [30.00dB] [on]
Front Right: Capture 46 [100%] [30.00dB] [on]
Simple mixer control 'Capture',1
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 16 [35%] [0.00dB] [off]
Front Right: Capture 16 [35%] [0.00dB] [off]
Simple mixer control 'Auto-Mute Mode',0
Capabilities: enum
Items: 'Disabled' 'Enabled'
Item0: 'Enabled'
Simple mixer control 'Channel Mode',0
Capabilities: enum
Items: '2ch' '4ch' '6ch'
Item0: '2ch'
Simple mixer control 'Input Source',0
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Internal Mic'
Simple mixer control 'Input Source',1
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Mic'
Simple mixer control 'Internal Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Internal Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]

#10 lore raw

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 120 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 119 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.
Quoted 8 lines
Quoted 1 line

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this). The converse might be true though - if you select "analog headphones" in pavucontrols the speakers go silent.

Julian

#11 lore raw

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

Quoted 2 lines

The converse might be true though - if you
select "analog headphones" in pavucontrols the speakers go silent.

This is what PA does intentionally, independently from the driver auto-mute behavior.

Takashi

#12 lore raw

W dniu 27.06.2011 08:04, Takashi Iwai pisze:

Quoted 138 lines

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

Quoted 3 lines

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

You are right - when auto-mute is disabled sound goes via both speakers and headphones when they are plugged. I did not know the function of auto-mute.
However, the "Speaker" and "Headphone" controls still do influence both outputs, and "Speaker" can only be muted - there is no volume control available. So, in my opinion, they should either be merged altogether, or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that is setting the volume of speakers and headphones independently.

Quoted 6 lines
Quoted 3 lines

The converse might be true though - if you
select "analog headphones" in pavucontrols the speakers go silent.

This is what PA does intentionally, independently from the driver auto-mute behavior.

OK, understood.

Quoted 1 line

Takashi

Julian

#13 lore raw

At Mon, 27 Jun 2011 08:21:26 +0200,

Quoted 144 lines · Julian Sikorski

W dniu 27.06.2011 08:04, Takashi Iwai pisze:

Quoted 138 lines

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 sound, and there are two configs showing up in pavucontrol (analog output and analog headphones) which seem to be the same. I have uploaded the output of alsa-info.sh [2]. Please let me know if more information is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

Quoted 3 lines

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

Quoted 8 lines

You are right - when auto-mute is disabled sound goes via both speakers and headphones when they are plugged. I did not know the function of auto-mute.
However, the "Speaker" and "Headphone" controls still do influence both outputs, and "Speaker" can only be muted - there is no volume control available. So, in my opinion, they should either be merged altogether, or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that is setting the volume of speakers and headphones independently.

Give alsa-info.sh outputs on your machine with the latest status for further analysis.

Takashi

#14 lore raw

At Mon, 27 Jun 2011 11:19:36 +0200,

Quoted 156 lines · Takashi Iwai

At Mon, 27 Jun 2011 08:21:26 +0200,

Quoted 144 lines · Julian Sikorski

W dniu 27.06.2011 08:04, Takashi Iwai pisze:

Quoted 138 lines

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,

Quoted 15 lines · Julian Sikorski

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently
got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in
microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1
sound, and there are two configs showing up in pavucontrol (analog
output and analog headphones) which seem to be the same. I have uploaded
the output of alsa-info.sh [2]. Please let me know if more information
is needed.

The current parser doesn't allow the multi-io pins when the primary output is no line-out. The patch below should fix (change) the behavior. It'll count HP out, too.

Takashi

---

sound/pci/hda/patch_realtek.c +14 -1
index fe56b2b..b0cf726 100644
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
   	hda_nid_t dac;
 
   	spec->multiout.dac_nids = spec->private_dac_nids;
+	spec->multiout.num_dacs = 0;
   	for (i = 0; i<   cfg->line_outs; i++) {
   		dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
   		if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   	unsigned int location, defcfg;
   	int num_pins;
 
+	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&&   cfg->hp_outs == 1) {
+		/* use HP as primary out */
+		cfg->speaker_outs = cfg->line_outs;
+		memcpy(cfg->speaker_pins, cfg->line_out_pins,
+		       sizeof(cfg->speaker_pins));
+		cfg->line_outs = cfg->hp_outs;
+		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+		cfg->hp_outs = 0;
+		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		cfg->line_out_type = AUTO_PIN_HP_OUT;
+		alc662_auto_fill_dac_nids(codec, cfg);
+	}
   	if (cfg->line_outs != 1 ||
-	    cfg->line_out_type != AUTO_PIN_LINE_OUT)
+	    cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
   		return 0;
 
Quoted 12 lines

sound/pci/hda/patch_realtek.c static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) · line 19368

Quoted 10 lines
sound/pci/hda/patch_realtek.c +2 -0
   	defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
   		spec->multi_ios = num_pins;
   		spec->ext_channel_count = 2;
   		spec->multiout.num_dacs = num_pins + 1;
+		/* for avoiding multi HP mixers */
+		cfg->line_out_type = AUTO_PIN_LINE_OUT;
   	}
   	return 0;
   }

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

Quoted 3 lines

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

Quoted 8 lines

You are right - when auto-mute is disabled sound goes via both speakers and headphones when they are plugged. I did not know the function of auto-mute.
However, the "Speaker" and "Headphone" controls still do influence both outputs, and "Speaker" can only be muted - there is no volume control available. So, in my opinion, they should either be merged altogether, or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that is setting the volume of speakers and headphones independently.

Quoted 2 lines

Give alsa-info.sh outputs on your machine with the latest status for further analysis.

I think this issue was fixed now in topic/hda branch in sound git tree:
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

#15 lore raw
Quoted 161 lines · Takashi Iwai

At Mon, 27 Jun 2011 11:19:36 +0200,

Quoted 156 lines · Takashi Iwai

At Mon, 27 Jun 2011 08:21:26 +0200,

Quoted 144 lines · Julian Sikorski

W dniu 27.06.2011 08:04, Takashi Iwai pisze:

Quoted 138 lines

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,
Julian Sikorski wrote:

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently
got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in
microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1
sound, and there are two configs showing up in pavucontrol (analog
output and analog headphones) which seem to be the same. I have uploaded
the output of alsa-info.sh [2]. Please let me know if more information
is needed.

The current parser doesn't allow the multi-io pins when the primary
output is no line-out. The patch below should fix (change) the
behavior. It'll count HP out, too.

Takashi

---
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index fe56b2b..b0cf726 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
hda_nid_t dac;

spec->multiout.dac_nids = spec->private_dac_nids;
+ spec->multiout.num_dacs = 0;
for (i = 0; i< cfg->line_outs; i++) {
dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
unsigned int location, defcfg;
int num_pins;

+ if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&& cfg->hp_outs == 1) {
+ /* use HP as primary out */
+ cfg->speaker_outs = cfg->line_outs;
+ memcpy(cfg->speaker_pins, cfg->line_out_pins,
+ sizeof(cfg->speaker_pins));
+ cfg->line_outs = cfg->hp_outs;
+ memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+ cfg->hp_outs = 0;
+ memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+ cfg->line_out_type = AUTO_PIN_HP_OUT;
+ alc662_auto_fill_dac_nids(codec, cfg);
+ }
if (cfg->line_outs != 1 ||
- cfg->line_out_type != AUTO_PIN_LINE_OUT)
+ cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
return 0;

Quoted 12 lines
Quoted 10 lines

defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
spec->multi_ios = num_pins;
spec->ext_channel_count = 2;
spec->multiout.num_dacs = num_pins + 1;
+ /* for avoiding multi HP mixers */
+ cfg->line_out_type = AUTO_PIN_LINE_OUT;
}
return 0;
}

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

Quoted 3 lines

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

Quoted 8 lines

You are right - when auto-mute is disabled sound goes via both speakers and headphones when they are plugged. I did not know the function of auto-mute.
However, the "Speaker" and "Headphone" controls still do influence both outputs, and "Speaker" can only be muted - there is no volume control available. So, in my opinion, they should either be merged altogether, or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that is setting the volume of speakers and headphones independently.

Quoted 2 lines

Give alsa-info.sh outputs on your machine with the latest status for further analysis.

Quoted 8 lines

I think this issue was fixed now in topic/hda branch in sound git tree:

   git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

Do you mean this specific commit:
http://git.kernel.org/?p=linux/kernel/git/tiwai/sound-2.6.git;a=commit;h=3af9ee6b83c4c3f2577719e31e7d2af1ce996557
?
The thing is that I only know how to build a kernel using Fedora RPM and I have never built it purely from source. As a result, I can easily test patches but testing whole trees might be tricky. If it is a problem, I can try to seek help how to create RPM out of your tree. I'll try to test it one way or the other once I get back home in the evening (I'm in CEST time zone).
Thank you for all the input so far.

Julian

#16 lore raw

At Mon, 27 Jun 2011 14:42:08 +0200,

Quoted 4 lines · Julian Sikorski
Quoted 4 lines

I think this issue was fixed now in topic/hda branch in sound git tree:

   git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git
Quoted 8 lines
Quoted 5 lines

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

Do you mean this specific commit:
http://git.kernel.org/?p=linux/kernel/git/tiwai/sound-2.6.git;a=commit;h=3af9ee6b83c4c3f2577719e31e7d2af1ce996557
?

Yes. But the commit depends on other older commits, so you can't do cherry-pick easily.

Takashi

#17 lore raw
Quoted 15 lines · Takashi Iwai

At Mon, 27 Jun 2011 14:42:08 +0200,

Quoted 4 lines · Julian Sikorski
Quoted 4 lines

I think this issue was fixed now in topic/hda branch in sound git tree:

    git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git
Quoted 8 lines
Quoted 5 lines

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

Do you mean this specific commit:
http://git.kernel.org/?p=linux/kernel/git/tiwai/sound-2.6.git;a=commit;h=3af9ee6b83c4c3f2577719e31e7d2af1ce996557
?

Quoted 5 lines

Yes. But the commit depends on other older commits, so you can't do cherry-pick easily.

Takashi

OK, how about obtaining a diff against Linus's tree? Would that work? Moreover, does this tree include the two patches you asked me to test earlier?

Julian

#18 lore raw

At Mon, 27 Jun 2011 14:55:14 +0200,

Quoted 17 lines · Julian Sikorski
Quoted 15 lines · Takashi Iwai

At Mon, 27 Jun 2011 14:42:08 +0200,

Quoted 12 lines · Julian Sikorski
Quoted 9 lines

I think this issue was fixed now in topic/hda branch in sound git tree:

    git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

Do you mean this specific commit:
http://git.kernel.org/?p=linux/kernel/git/tiwai/sound-2.6.git;a=commit;h=3af9ee6b83c4c3f2577719e31e7d2af1ce996557
?

Quoted 6 lines
Quoted 5 lines

Yes. But the commit depends on other older commits, so you can't do cherry-pick easily.

Takashi

OK, how about obtaining a diff against Linus's tree? Would that work?

It should work, of course. It's something like what git-merge does :) But beware that it'll be a big patch with 12736 lines.

Quoted 2 lines

Moreover, does this tree include the two patches you asked me to test earlier?

Yes.

Takashi

#19 lore raw
In reply to Takashi Iwai

W dniu 27.06.2011 14:32, Takashi Iwai pisze:

Quoted 161 lines

At Mon, 27 Jun 2011 11:19:36 +0200,

Quoted 156 lines · Takashi Iwai

At Mon, 27 Jun 2011 08:21:26 +0200,

Quoted 144 lines · Julian Sikorski

W dniu 27.06.2011 08:04, Takashi Iwai pisze:

Quoted 138 lines

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 61 lines · Julian Sikorski
Quoted 59 lines · Takashi Iwai

At Thu, 23 Jun 2011 08:36:55 +0200,
Julian Sikorski wrote:

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently
got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in
microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1
sound, and there are two configs showing up in pavucontrol (analog
output and analog headphones) which seem to be the same. I have uploaded
the output of alsa-info.sh [2]. Please let me know if more information
is needed.

The current parser doesn't allow the multi-io pins when the primary
output is no line-out. The patch below should fix (change) the
behavior. It'll count HP out, too.

Takashi

---
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index fe56b2b..b0cf726 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
hda_nid_t dac;

spec->multiout.dac_nids = spec->private_dac_nids;
+ spec->multiout.num_dacs = 0;
for (i = 0; i< cfg->line_outs; i++) {
dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
unsigned int location, defcfg;
int num_pins;

+ if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&& cfg->hp_outs == 1) {
+ /* use HP as primary out */
+ cfg->speaker_outs = cfg->line_outs;
+ memcpy(cfg->speaker_pins, cfg->line_out_pins,
+ sizeof(cfg->speaker_pins));
+ cfg->line_outs = cfg->hp_outs;
+ memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+ cfg->hp_outs = 0;
+ memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+ cfg->line_out_type = AUTO_PIN_HP_OUT;
+ alc662_auto_fill_dac_nids(codec, cfg);
+ }
if (cfg->line_outs != 1 ||
- cfg->line_out_type != AUTO_PIN_LINE_OUT)
+ cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
return 0;

Quoted 12 lines
Quoted 10 lines

defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
spec->multi_ios = num_pins;
spec->ext_channel_count = 2;
spec->multiout.num_dacs = num_pins + 1;
+ /* for avoiding multi HP mixers */
+ cfg->line_out_type = AUTO_PIN_LINE_OUT;
}
return 0;
}

Would you like me to test this patch? If so, what should I apply it to and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

Quoted 3 lines

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

Quoted 8 lines

You are right - when auto-mute is disabled sound goes via both speakers and headphones when they are plugged. I did not know the function of auto-mute.
However, the "Speaker" and "Headphone" controls still do influence both outputs, and "Speaker" can only be muted - there is no volume control available. So, in my opinion, they should either be merged altogether, or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that is setting the volume of speakers and headphones independently.

Quoted 2 lines

Give alsa-info.sh outputs on your machine with the latest status for further analysis.

Quoted 8 lines

I think this issue was fixed now in topic/hda branch in sound git tree:
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

It seems like the problem is still there. The output of alsa-info.sh is available here:
http://www.alsa-project.org/db/?f=38e2e44ab86691006a837715601aad4311fda0d3

Julian

#20 lore raw

At Mon, 27 Jun 2011 22:08:29 +0200,

Quoted 166 lines · Julian Sikorski

W dniu 27.06.2011 14:32, Takashi Iwai pisze:

Quoted 164 lines

At Mon, 27 Jun 2011 11:19:36 +0200,

Quoted 156 lines · Takashi Iwai

At Mon, 27 Jun 2011 08:21:26 +0200,

Quoted 144 lines · Julian Sikorski

W dniu 27.06.2011 08:04, Takashi Iwai pisze:

Quoted 138 lines

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 77 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,

Quoted 73 lines · Julian Sikorski

On 23/06/2011 14:41, Takashi Iwai wrote:
At Thu, 23 Jun 2011 08:36:55 +0200,
Julian Sikorski wrote:

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently
got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in
microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1
sound, and there are two configs showing up in pavucontrol (analog
output and analog headphones) which seem to be the same. I have uploaded
the output of alsa-info.sh [2]. Please let me know if more information
is needed.

The current parser doesn't allow the multi-io pins when the primary
output is no line-out. The patch below should fix (change) the
behavior. It'll count HP out, too.

Takashi

---
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index fe56b2b..b0cf726 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
hda_nid_t dac;

spec->multiout.dac_nids = spec->private_dac_nids;
+ spec->multiout.num_dacs = 0;
for (i = 0; i< cfg->line_outs; i++) {
dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
unsigned int location, defcfg;
int num_pins;

+ if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&& cfg->hp_outs == 1) {
+ /* use HP as primary out */
+ cfg->speaker_outs = cfg->line_outs;
+ memcpy(cfg->speaker_pins, cfg->line_out_pins,
+ sizeof(cfg->speaker_pins));
+ cfg->line_outs = cfg->hp_outs;
+ memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+ cfg->hp_outs = 0;
+ memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+ cfg->line_out_type = AUTO_PIN_HP_OUT;
+ alc662_auto_fill_dac_nids(codec, cfg);
+ }
if (cfg->line_outs != 1 ||
- cfg->line_out_type != AUTO_PIN_LINE_OUT)
+ cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
return 0;

defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
spec->multi_ios = num_pins;
spec->ext_channel_count = 2;
spec->multiout.num_dacs = num_pins + 1;
+ /* for avoiding multi HP mixers */
+ cfg->line_out_type = AUTO_PIN_LINE_OUT;
}
return 0;
}
Would you like me to test this patch? If so, what should I apply it to
and how should I proceed?

Quoted 2 lines

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

Quoted 3 lines

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

Quoted 8 lines

You are right - when auto-mute is disabled sound goes via both speakers and headphones when they are plugged. I did not know the function of auto-mute.
However, the "Speaker" and "Headphone" controls still do influence both outputs, and "Speaker" can only be muted - there is no volume control available. So, in my opinion, they should either be merged altogether, or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that is setting the volume of speakers and headphones independently.

Quoted 2 lines

Give alsa-info.sh outputs on your machine with the latest status for further analysis.

I think this issue was fixed now in topic/hda branch in sound git tree:
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git

Quoted 8 lines
Quoted 5 lines

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

It seems like the problem is still there. The output of alsa-info.sh is available here:
http://www.alsa-project.org/db/?f=38e2e44ab86691006a837715601aad4311fda0d3

Double-check whether you compiled really the right stuff. The emulator works fine, so something wrong likely in your side.

Takashi

#21 lore raw
Quoted 5 lines · Takashi Iwai

Double-check whether you compiled really the right stuff. The emulator works fine, so something wrong likely in your side.

Takashi

When I was asking for help how to build a different kernel tree and a fellow #fedora-kernel channel member offered to compile the stuff for me. The source RPM is here:
http://koji.fedoraproject.org/koji/taskinfo?taskID=3164043
Inside, you have alsa-fixups.patch and alsa-next_topic-hda.patch as an addition to the stock Fedora kernel. I looked into alsa-next_topic-hda.patch and it seemed like commit
http://git.kernel.org/?p=linux/kernel/git/tiwai/sound-2.6.git;a=commit;h=3af9ee6b83c4c3f2577719e31e7d2af1ce996557
was included.

Julian

#22 lore raw

At Tue, 28 Jun 2011 10:03:34 +0200,

Quoted 7 lines · Julian Sikorski
Quoted 5 lines · Takashi Iwai

Double-check whether you compiled really the right stuff. The emulator works fine, so something wrong likely in your side.

Takashi

Quoted 9 lines

When I was asking for help how to build a different kernel tree and a fellow #fedora-kernel channel member offered to compile the stuff for me. The source RPM is here:
http://koji.fedoraproject.org/koji/taskinfo?taskID=3164043
Inside, you have alsa-fixups.patch and alsa-next_topic-hda.patch as an addition to the stock Fedora kernel. I looked into alsa-next_topic-hda.patch and it seemed like commit
http://git.kernel.org/?p=linux/kernel/git/tiwai/sound-2.6.git;a=commit;h=3af9ee6b83c4c3f2577719e31e7d2af1ce996557
was included.

That doesn't explain anything, and I can't help any more, sorry. The single patch won't work unless you really carefully pick up all necessary stuff. You'd better to copy the whole sound/pci/hda/* files from the very latest sound git tree.

Any reason you can't use git and build manually?
It'll save your time very much in the end.
With a modern PC, you can build the kernel in 10 minutes or so if you edit kernel config beforehand.

Takashi

#23 lore raw
Quoted 24 lines · Takashi Iwai

At Tue, 28 Jun 2011 10:03:34 +0200,

Quoted 7 lines · Julian Sikorski
Quoted 5 lines · Takashi Iwai

Double-check whether you compiled really the right stuff. The emulator works fine, so something wrong likely in your side.

Takashi

Quoted 9 lines

When I was asking for help how to build a different kernel tree and a fellow #fedora-kernel channel member offered to compile the stuff for me. The source RPM is here:
http://koji.fedoraproject.org/koji/taskinfo?taskID=3164043
Inside, you have alsa-fixups.patch and alsa-next_topic-hda.patch as an addition to the stock Fedora kernel. I looked into alsa-next_topic-hda.patch and it seemed like commit
http://git.kernel.org/?p=linux/kernel/git/tiwai/sound-2.6.git;a=commit;h=3af9ee6b83c4c3f2577719e31e7d2af1ce996557
was included.

That doesn't explain anything, and I can't help any more, sorry. The single patch won't work unless you really carefully pick up all necessary stuff. You'd better to copy the whole sound/pci/hda/* files from the very latest sound git tree.

Quoted 7 lines

Any reason you can't use git and build manually?
It'll save your time very much in the end.
With a modern PC, you can build the kernel in 10 minutes or so if you edit kernel config beforehand.

Takashi

I just never did it and I am not sure how to steal the old config options. Would make oldconfig do the trick?

Julian

#24 lore raw

At Tue, 28 Jun 2011 12:36:44 +0200,

Quoted 32 lines · Julian Sikorski
Quoted 30 lines · Takashi Iwai

At Tue, 28 Jun 2011 10:03:34 +0200,

Quoted 7 lines · Julian Sikorski
Quoted 5 lines · Takashi Iwai

Double-check whether you compiled really the right stuff. The emulator works fine, so something wrong likely in your side.

Takashi

Quoted 9 lines

When I was asking for help how to build a different kernel tree and a fellow #fedora-kernel channel member offered to compile the stuff for me. The source RPM is here:
http://koji.fedoraproject.org/koji/taskinfo?taskID=3164043
Inside, you have alsa-fixups.patch and alsa-next_topic-hda.patch as an addition to the stock Fedora kernel. I looked into alsa-next_topic-hda.patch and it seemed like commit
http://git.kernel.org/?p=linux/kernel/git/tiwai/sound-2.6.git;a=commit;h=3af9ee6b83c4c3f2577719e31e7d2af1ce996557
was included.

That doesn't explain anything, and I can't help any more, sorry. The single patch won't work unless you really carefully pick up all necessary stuff. You'd better to copy the whole sound/pci/hda/* files from the very latest sound git tree.

Any reason you can't use git and build manually?
It'll save your time very much in the end.
With a modern PC, you can build the kernel in 10 minutes or so if you edit kernel config beforehand.

Quoted 3 lines
Quoted 1 line

Takashi

I just never did it and I am not sure how to steal the old config options. Would make oldconfig do the trick?

Yes, and just press return for the questions.

Or you can try make localmodconfig. This will give you a .config with only the currently used modules, so many unused config items are stripped down.

Note that you need to load some dynamically loaded modules (e.g. usb stuff) before running the localmodconfig. Otherwise the modules won't be built for the new kernel.

Takashi

#25 lore raw
In reply to Takashi Iwai

W dniu 28.06.2011 09:12, Takashi Iwai pisze:

Quoted 177 lines

At Mon, 27 Jun 2011 22:08:29 +0200,

Quoted 166 lines · Julian Sikorski

W dniu 27.06.2011 14:32, Takashi Iwai pisze:

Quoted 164 lines

At Mon, 27 Jun 2011 11:19:36 +0200,

Quoted 156 lines · Takashi Iwai

At Mon, 27 Jun 2011 08:21:26 +0200,

Quoted 144 lines · Julian Sikorski

W dniu 27.06.2011 08:04, Takashi Iwai pisze:

Quoted 138 lines

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,

Quoted 79 lines · Takashi Iwai

At Thu, 23 Jun 2011 18:40:47 +0200,
Julian Sikorski wrote:

On 23/06/2011 14:41, Takashi Iwai wrote:
At Thu, 23 Jun 2011 08:36:55 +0200,
Julian Sikorski wrote:

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently
got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in
microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1
sound, and there are two configs showing up in pavucontrol (analog
output and analog headphones) which seem to be the same. I have uploaded
the output of alsa-info.sh [2]. Please let me know if more information
is needed.

The current parser doesn't allow the multi-io pins when the primary
output is no line-out. The patch below should fix (change) the
behavior. It'll count HP out, too.

Takashi

---
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index fe56b2b..b0cf726 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
hda_nid_t dac;

spec->multiout.dac_nids = spec->private_dac_nids;
+ spec->multiout.num_dacs = 0;
for (i = 0; i< cfg->line_outs; i++) {
dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
unsigned int location, defcfg;
int num_pins;

+ if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&& cfg->hp_outs == 1) {
+ /* use HP as primary out */
+ cfg->speaker_outs = cfg->line_outs;
+ memcpy(cfg->speaker_pins, cfg->line_out_pins,
+ sizeof(cfg->speaker_pins));
+ cfg->line_outs = cfg->hp_outs;
+ memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+ cfg->hp_outs = 0;
+ memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+ cfg->line_out_type = AUTO_PIN_HP_OUT;
+ alc662_auto_fill_dac_nids(codec, cfg);
+ }
if (cfg->line_outs != 1 ||
- cfg->line_out_type != AUTO_PIN_LINE_OUT)
+ cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
return 0;

defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
spec->multi_ios = num_pins;
spec->ext_channel_count = 2;
spec->multiout.num_dacs = num_pins + 1;
+ /* for avoiding multi HP mixers */
+ cfg->line_out_type = AUTO_PIN_LINE_OUT;
}
return 0;
}
Would you like me to test this patch? If so, what should I apply it to
and how should I proceed?

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch" for using the surround outputs even with these patches. As default, it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

Quoted 3 lines

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

Quoted 8 lines

You are right - when auto-mute is disabled sound goes via both speakers and headphones when they are plugged. I did not know the function of auto-mute.
However, the "Speaker" and "Headphone" controls still do influence both outputs, and "Speaker" can only be muted - there is no volume control available. So, in my opinion, they should either be merged altogether, or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that is setting the volume of speakers and headphones independently.

Quoted 2 lines

Give alsa-info.sh outputs on your machine with the latest status for further analysis.

I think this issue was fixed now in topic/hda branch in sound git tree:
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git

Quoted 8 lines
Quoted 5 lines

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

It seems like the problem is still there. The output of alsa-info.sh is available here:
http://www.alsa-project.org/db/?f=38e2e44ab86691006a837715601aad4311fda0d3

Quoted 5 lines

Double-check whether you compiled really the right stuff. The emulator works fine, so something wrong likely in your side.

Takashi

I compiled the latest origin/master of sound-2.6 tree and the problem is still there. Output of alsa-info.sh is attached.

Julian

upload=true&script=true&cardinfo=
!!################################
!!ALSA Information Script v 0.4.60
!!################################

!!Script ran on: Wed Jun 29 17:30:29 UTC 2011

!!Linux Distribution
!!------------------

Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock)

!!DMI Information
!!---------------

Manufacturer:      CLEVO                            
Product Name:      P150HMx
Product Version:   Not Applicable                    

!!Kernel Information
!!------------------

Kernel release:    3.0-0.rc2.git0.1.belegdol2.fc15.x86_64
Operating System:  GNU/Linux
Architecture:      x86_64
Processor:         x86_64
SMP Enabled:       Yes

!!ALSA Version
!!------------

Driver version:     1.0.24
Library version:    1.0.24
Utilities version:  1.0.24.1

!!Loaded ALSA modules
!!-------------------

snd_hda_intel
snd_hda_intel

!!Sound Servers on this system
!!----------------------------

Pulseaudio:
Installed - Yes (/usr/bin/pulseaudio)
Running - Yes

Jack:
Installed - Yes (/usr/bin/jackd)
Running - No

!!Soundcards recognised by ALSA
!!-----------------------------

0 [PCH ]: HDA-Intel - HDA Intel PCH

                      HDA Intel PCH at 0xf6500000 irq 56
 1 [NVidia         ]: HDA-Intel - HDA NVidia
                      HDA NVidia at 0xf6080000 irq 17

!!PCI Soundcards installed in the system
!!--------------------------------------

00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 01:00.1 Audio device: nVidia Corporation Device 0beb (rev a1)

!!Advanced information - PCI Vendor/Device/Subsystem ID's !!--------------------------------------------------------

00:1b.0 0403: 8086:1c20 (rev 05)

	Subsystem: 1558:5102
--
01:00.1 0403: 10de:0beb (rev a1)
	Subsystem: 1558:5102

!!Loaded sound module options
!!--------------------------

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!HDA-Intel Codec information
!!---------------------------
--startcollapse--

Codec: Realtek ALC892
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0892
Subsystem Id: 0x15585102
Revision Id: 0x100302
No Modem Function Group found
Default PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Device: name="ALC892 Analog", type="Audio", device=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x40 0x40]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Surround Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x40 0x40]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Center Playback Volume", index=0, device=0

    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Volume", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x40 0x40]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x05 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0 Amp-Out vals: [0x40 0x40]
Converter: stream=0, channel=0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Control: name="IEC958 Default PCM Playback Switch", index=0, device=0
Device: name="ALC892 Digital", type="SPDIF", device=1
Converter: stream=5, channel=0
Digital: Enabled
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=1, device=0
Control: name="Capture Volume", index=1, device=0 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x90 0x90]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x23

Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=0, device=0
Control: name="Capture Volume", index=0, device=0
Device: name="ALC892 Analog", type="Audio", device=0 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x2e 0x2e]
Converter: stream=1, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x22

Node 0x0a [Audio Input] wcaps 0x100711: Stereo Digital
Converter: stream=0, channel=0
SDI-Select: 0
Digital:
Digital category: 0x0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x1f
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Internal Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Internal Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Line Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Control: name="Line Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
  Amp-In vals:  [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
  Connection: 10
     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17
Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Headphone Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x00 0x00]
  Connection: 2
     0x02 0x0b
Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Surround Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x80 0x80]
  Connection: 2
     0x03 0x0b
Node 0x0e [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Center Playback Switch", index=0, device=0
    ControlAmp: chs=1, dir=In, idx=0, ofs=0
  Control: name="LFE Playback Switch", index=0, device=0
    ControlAmp: chs=2, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x80 0x80]
  Connection: 2
     0x04 0x0b

Node 0x0f [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x05 0x0b

Node 0x10 [Audio Output] wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x11 [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x10

Node 0x12 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x0001003e: IN OUT HP EAPD Detect Trigger
  EAPD 0x2: EAPD
  Pin Default 0x99130110: [Fixed] Speaker at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x0c

Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0d

Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0e

Node 0x17 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0f
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x03 0x03]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x01a11c30: [Jack] Mic at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0x0
  Pin-ctls: 0x21: IN VREF_50
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x19 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Internal Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x0000373e: IN OUT HP Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x99a30931: [Fixed] Mic at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x3, Sequence = 0x1
    Misc = NO_PRESENCE
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26

Node 0x1a [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00003736: IN OUT Detect Trigger

    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x0181143f: [Jack] Line In at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0xf
  Pin-ctls: 0x20: IN VREF_HIZ
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26

Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00]
Pincap 0x0001373e: IN OUT HP EAPD Detect Trigger

    Vref caps: HIZ 50 GRD 80 100
  EAPD 0x2: EAPD
  Pin Default 0x0121101f: [Jack] HP Out at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x1, Sequence = 0xf
  Pin-ctls: 0xc0: OUT HP VREF_HIZ
  Unsolicited: tag=04, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26

Node 0x1c [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x00000024: IN Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1d [Pin Complex] wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x598301f0: [N/A] Line In at Int ATAPI
Conn = ATAPI, Color = Unknown DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x01451120: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = Black DefAssociation = 0x2, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x06

Node 0x1f [Pin Complex] wcaps 0x400681: Stereo Digital
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=24
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=0, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x80 0x80] [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 12

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b 0x12

Node 0x23 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=1, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 11

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b

Node 0x24 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x25 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0 Amp-Out vals: [0x40 0x40]
Converter: stream=0, channel=0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x26 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x25 0x0b

Codec: Nvidia GPU 12 HDMI/DP
Address: 0
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=6, channel=0
Digital: Enabled GenLevel
Digital category: 0x2
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 1
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=2, device=0
Control: name="IEC958 Playback Pro Mask", index=2, device=0
Control: name="IEC958 Playback Default", index=2, device=0
Control: name="IEC958 Playback Switch", index=2, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 3
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=3, device=0
Control: name="IEC958 Playback Pro Mask", index=3, device=0
Control: name="IEC958 Playback Default", index=3, device=0
Control: name="IEC958 Playback Switch", index=3, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

--endcollapse--

!!ALSA Device nodes
!!-----------------

crw-rw----+ 1 root audio 116, 6 Jun 29 19:27 /dev/snd/controlC0 crw-rw----+ 1 root audio 116, 15 Jun 29 19:27 /dev/snd/controlC1 crw-rw----+ 1 root audio 116, 5 Jun 29 19:27 /dev/snd/hwC0D0 crw-rw----+ 1 root audio 116, 14 Jun 29 19:27 /dev/snd/hwC1D0 crw-rw----+ 1 root audio 116, 13 Jun 29 19:27 /dev/snd/hwC1D1 crw-rw----+ 1 root audio 116, 12 Jun 29 19:27 /dev/snd/hwC1D2 crw-rw----+ 1 root audio 116, 11 Jun 29 19:27 /dev/snd/hwC1D3

crw-rw----+ 1 root audio 116,  4 Jun 29 19:28 /dev/snd/pcmC0D0c
crw-rw----+ 1 root audio 116,  3 Jun 29 19:29 /dev/snd/pcmC0D0p
crw-rw----+ 1 root audio 116,  2 Jun 29 19:28 /dev/snd/pcmC0D1p
crw-rw----+ 1 root audio 116, 10 Jun 29 19:28 /dev/snd/pcmC1D3p
crw-rw----+ 1 root audio 116,  9 Jun 29 19:27 /dev/snd/pcmC1D7p
crw-rw----+ 1 root audio 116,  8 Jun 29 19:27 /dev/snd/pcmC1D8p
crw-rw----+ 1 root audio 116,  7 Jun 29 19:27 /dev/snd/pcmC1D9p
crw-rw----+ 1 root audio 116,  1 Jun 29 19:27 /dev/snd/seq

crw-rw----+ 1 root audio 116, 33 Jun 29 19:27 /dev/snd/timer

/dev/snd/by-path:
total 0
drwxr-xr-x. 2 root root 80 Jun 29 19:27 .
drwxr-xr-x. 3 root root 380 Jun 29 19:27 ..
lrwxrwxrwx. 1 root root 12 Jun 29 19:27 pci-0000:00:1b.0 -> ../controlC0 lrwxrwxrwx. 1 root root 12 Jun 29 19:27 pci-0000:01:00.1 -> ../controlC1

!!ALSA configuration files
!!------------------------

!!System wide config file (/etc/asound.conf)

#
# Place your global alsa-lib configuration here... #

@hooks [

	{
		func load
		files [
			"/etc/alsa/pulse-default.conf"
		]
		errors false
	}

]

!!Aplay/Arecord output
!!------------

APLAY

**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0

ARECORD

**** List of CAPTURE Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0

!!Amixer output
!!-------------

!!-------Mixer controls for card 0 [PCH]

Card hw:0 'PCH'/'HDA Intel PCH at 0xf6500000 irq 56'
Mixer name : 'Realtek ALC892'
Components : 'HDA:10ec0892,15585102,00100302'
Controls : 33
Simple ctrls : 20
Simple mixer control 'Master',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Headphone',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Speaker',0
Capabilities: pswitch penum
Playback channels: Front Left - Front Right
Mono:
Front Left: Playback [on]
Front Right: Playback [on]
Simple mixer control 'PCM',0
Capabilities: pvolume penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 255 [100%] [0.00dB]
Front Right: Playback 255 [100%] [0.00dB]
Simple mixer control 'Surround',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Center',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'LFE',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Line',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 3 [100%] [30.00dB]
Front Right: 3 [100%] [30.00dB]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958 Default PCM',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 46 [100%] [30.00dB] [on]
Front Right: Capture 46 [100%] [30.00dB] [on]
Simple mixer control 'Capture',1
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 16 [35%] [0.00dB] [off]
Front Right: Capture 16 [35%] [0.00dB] [off]
Simple mixer control 'Auto-Mute Mode',0
Capabilities: enum
Items: 'Disabled' 'Enabled'
Item0: 'Enabled'
Simple mixer control 'Channel Mode',0
Capabilities: enum
Items: '2ch' '4ch' '6ch'
Item0: '2ch'
Simple mixer control 'Input Source',0
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Internal Mic'
Simple mixer control 'Input Source',1
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Mic'
Simple mixer control 'Internal Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Internal Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]

!!-------Mixer controls for card 1 [NVidia]

Card hw:1 'NVidia'/'HDA NVidia at 0xf6080000 irq 17'
Mixer name : 'Nvidia GPU 12 HDMI/DP'
Components : 'HDA:10de0012,10de0101,00100100'
Controls : 16
Simple ctrls : 4
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958',1
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',2
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',3
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]

!!Alsactl output
!!-------------

--startcollapse--

state.PCH {
	control.1 {
		iface MIXER
		name 'Channel Mode'
		value '2ch'
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 '2ch'
			item.1 '4ch'
			item.2 '6ch'
		}
	}
	control.2 {
		iface MIXER
		name 'Headphone Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.3 {
		iface MIXER
		name 'Headphone Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.4 {
		iface MIXER
		name 'Surround Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.5 {
		iface MIXER
		name 'Surround Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.6 {
		iface MIXER
		name 'Center Playback Volume'
		value 64
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
		}
	}
	control.7 {
		iface MIXER
		name 'LFE Playback Volume'
		value 64
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
		}
	}
	control.8 {
		iface MIXER
		name 'Center Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'LFE Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'Speaker Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.11 {
		iface MIXER
		name 'Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.12 {
		iface MIXER
		name 'Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.13 {
		iface MIXER
		name 'Internal Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.14 {
		iface MIXER
		name 'Internal Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.15 {
		iface MIXER
		name 'Line Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.16 {
		iface MIXER
		name 'Line Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.17 {
		iface MIXER
		name 'Mic Boost Volume'
		value.0 3
		value.1 3
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 3000
			dbvalue.1 3000
		}
	}
	control.18 {
		iface MIXER
		name 'Internal Mic Boost Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.19 {
		iface MIXER
		name 'Auto-Mute Mode'
		value Enabled
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Disabled
			item.1 Enabled
		}
	}
	control.20 {
		iface MIXER
		name 'Capture Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.21 {
		iface MIXER
		name 'Capture Switch'
		index 1
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.22 {
		iface MIXER
		name 'Capture Volume'
		value.0 46
		value.1 46
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 3000
			dbvalue.1 3000
		}
	}
	control.23 {
		iface MIXER
		name 'Capture Volume'
		index 1
		value.0 16
		value.1 16
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.24 {
		iface MIXER
		name 'Input Source'
		value 'Internal Mic'
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.25 {
		iface MIXER
		name 'Input Source'
		index 1
		value Mic
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.26 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.27 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.28 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.29 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.30 {
		iface MIXER
		name 'IEC958 Default PCM Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.31 {
		iface MIXER
		name 'Master Playback Volume'
		value 64
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
		}
	}
	control.32 {
		iface MIXER
		name 'Master Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.33 {
		iface MIXER
		name 'PCM Playback Volume'
		value.0 255
		value.1 255
		comment {
			access 'read write user'
			type INTEGER
			count 2
			range '0 - 255'
			tlv '0000000100000008ffffec1400000014'
			dbmin -5100
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
}
state.NVidia {
	control.1 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.2 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.3 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.4 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.5 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 1
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.6 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 1
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.7 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 1
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.8 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 1
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 2
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 2
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.11 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 2
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.12 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 2
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.13 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 3
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.14 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 3
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.15 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 3
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.16 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 3
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
}

--endcollapse--

!!All Loaded Modules
!!------------------

Module
ebtable_nat
ebtables
ipt_MASQUERADE
iptable_nat
nf_nat
xt_CHECKSUM
iptable_mangle
bridge
stp
llc
sunrpc
cpufreq_ondemand
acpi_cpufreq
freq_table
mperf
bnep
bluetooth
nf_conntrack_ipv4
nf_defrag_ipv4
ip6t_REJECT
nf_conntrack_ipv6
nf_defrag_ipv6
xt_state
nf_conntrack
ip6table_filter
ip6_tables
fuse
arc4
uvcvideo
snd_hda_codec_hdmi
videodev
media
microcode
v4l2_compat_ioctl32
snd_hda_codec_realtek
joydev
snd_hda_intel
snd_hda_codec
serio_raw
pcspkr
snd_hwdep
snd_seq
i2c_i801
snd_seq_device
i2c_core
iTCO_wdt
iTCO_vendor_support
snd_pcm
iwlagn
mac80211
snd_timer
snd
xhci_hcd
jmb38x_ms
memstick
jme
cfg80211
rfkill
mii
soundcore
snd_page_alloc
virtio_net
kvm_intel
kvm
firewire_ohci
firewire_core
crc_itu_t
sdhci_pci
sdhci
mmc_core
wmi
video

!!Sysfs Files
!!-----------

/sys/class/sound/hwC0D0/init_pin_configs:
0x11 0x411111f0
0x12 0x411111f0
0x14 0x99130110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x411111f0
0x18 0x01a11c30
0x19 0x99a30931
0x1a 0x0181143f
0x1b 0x0121101f
0x1c 0x411111f0
0x1d 0x598301f0
0x1e 0x01451120
0x1f 0x411111f0

/sys/class/sound/hwC0D0/driver_pin_configs:

/sys/class/sound/hwC0D0/user_pin_configs:

/sys/class/sound/hwC0D0/init_verbs:

/sys/class/sound/hwC1D0/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D0/driver_pin_configs:

/sys/class/sound/hwC1D0/user_pin_configs:

/sys/class/sound/hwC1D0/init_verbs:

/sys/class/sound/hwC1D1/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D1/driver_pin_configs:

/sys/class/sound/hwC1D1/user_pin_configs:

/sys/class/sound/hwC1D1/init_verbs:

/sys/class/sound/hwC1D2/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D2/driver_pin_configs:

/sys/class/sound/hwC1D2/user_pin_configs:

/sys/class/sound/hwC1D2/init_verbs:

/sys/class/sound/hwC1D3/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D3/driver_pin_configs:

/sys/class/sound/hwC1D3/user_pin_configs:

/sys/class/sound/hwC1D3/init_verbs:

!!ALSA/HDA dmesg
!!------------------

[   19.861593] mtp-probe[622]: bus: 1, device: 3 was not an MTP device
[   19.896029] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   19.896237] snd_hda_intel 0000:00:1b.0: irq 56 for MSI/MSI-X
[   19.896377] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[   19.919918] mtp-probe[647]: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5"
[   19.960520] hda_codec: ALC892: SKU not ready 0x598301f0
[   19.960683] hda_codec: ALC892: BIOS auto-probing.
[   19.960690] ALSA sound/pci/hda/hda_codec.c:4831 autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   19.960693] ALSA sound/pci/hda/hda_codec.c:4835    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   19.960696] ALSA sound/pci/hda/hda_codec.c:4839    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   19.960698] ALSA sound/pci/hda/hda_codec.c:4840    mono: mono_out=0x0
[   19.960701] ALSA sound/pci/hda/hda_codec.c:4843    dig-out=0x1e/0x0
[   19.960703] ALSA sound/pci/hda/hda_codec.c:4844    inputs:
[   19.960706] ALSA sound/pci/hda/hda_codec.c:4848  Mic=0x18
[   19.960708] ALSA sound/pci/hda/hda_codec.c:4848  Internal Mic=0x19
[   19.960710] ALSA sound/pci/hda/hda_codec.c:4848  Line=0x1a
[   19.960712] ALSA sound/pci/hda/hda_codec.c:4850 
[   19.962063] ALSA sound/pci/hda/patch_realtek.c:1789 realtek: No valid SSID, checking pincfg 0x598301f0 for NID 0x1d
[   19.962066] ALSA sound/pci/hda/patch_realtek.c:1870 realtek: Enable default setup for auto mode as fallback
[   19.987178] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   20.035939] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   20.035956] hda_intel: Disabling MSI
[   20.036245] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[   20.043100] ALSA sound/pci/hda/hda_intel.c:1454 Enable delay in RIRB handling
[   20.103021] mtp-probe[647]: bus: 2, device: 3 was not an MTP device
--
[   20.277359] USB Video Class driver (v1.1.0)
[   20.295798] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
[   20.334784] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0
[   20.351207] iwlagn 0000:04:00.0: loaded firmware version 17.168.5.1 build 33993
[   20.357260] Registered led device: phy0-led
[   20.374714] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0
[   20.407236] microcode: CPU1 sig=0x206a7, pf=0x10, revision=0x14
[   20.413674] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[   20.434741] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13
[   20.435403] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[   20.436074] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[   20.436794] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[   20.438282] microcode: CPU2 sig=0x206a7, pf=0x10, revision=0x14
--
[   47.764496] DMAR:[fault reason 05] PTE Write access is not set
[   61.529629] hda-intel: Invalid position buffer, using LPIB read method instead.
[   61.715151] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
[   61.878197] hda-intel: Invalid position buffer, using LPIB read method instead.
[   72.242637] DRHD: handling fault status reg 2
#26 lore raw

W dniu 29.06.2011 19:36, Julian Sikorski pisze:

Quoted 182 lines

W dniu 28.06.2011 09:12, Takashi Iwai pisze:

Quoted 181 lines

At Mon, 27 Jun 2011 22:08:29 +0200,

Quoted 166 lines · Julian Sikorski

W dniu 27.06.2011 14:32, Takashi Iwai pisze:

Quoted 164 lines

At Mon, 27 Jun 2011 11:19:36 +0200,

Quoted 156 lines · Takashi Iwai

At Mon, 27 Jun 2011 08:21:26 +0200,

Quoted 144 lines · Julian Sikorski

W dniu 27.06.2011 08:04, Takashi Iwai pisze:

Quoted 138 lines

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 92 lines · Julian Sikorski
Quoted 90 lines · Takashi Iwai

At Fri, 24 Jun 2011 10:34:01 +0200,
Takashi Iwai wrote:

At Thu, 23 Jun 2011 18:40:47 +0200,
Julian Sikorski wrote:

On 23/06/2011 14:41, Takashi Iwai wrote:
At Thu, 23 Jun 2011 08:36:55 +0200,
Julian Sikorski wrote:

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently
got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in
microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1
sound, and there are two configs showing up in pavucontrol (analog
output and analog headphones) which seem to be the same. I have uploaded
the output of alsa-info.sh [2]. Please let me know if more information
is needed.

The current parser doesn't allow the multi-io pins when the primary
output is no line-out. The patch below should fix (change) the
behavior. It'll count HP out, too.

Takashi

---
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index fe56b2b..b0cf726 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
hda_nid_t dac;

spec->multiout.dac_nids = spec->private_dac_nids;
+ spec->multiout.num_dacs = 0;
for (i = 0; i< cfg->line_outs; i++) {
dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
unsigned int location, defcfg;
int num_pins;

+ if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&& cfg->hp_outs == 1) {
+ /* use HP as primary out */
+ cfg->speaker_outs = cfg->line_outs;
+ memcpy(cfg->speaker_pins, cfg->line_out_pins,
+ sizeof(cfg->speaker_pins));
+ cfg->line_outs = cfg->hp_outs;
+ memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+ cfg->hp_outs = 0;
+ memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+ cfg->line_out_type = AUTO_PIN_HP_OUT;
+ alc662_auto_fill_dac_nids(codec, cfg);
+ }
if (cfg->line_outs != 1 ||
- cfg->line_out_type != AUTO_PIN_LINE_OUT)
+ cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
return 0;

defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
spec->multi_ios = num_pins;
spec->ext_channel_count = 2;
spec->multiout.num_dacs = num_pins + 1;
+ /* for avoiding multi HP mixers */
+ cfg->line_out_type = AUTO_PIN_LINE_OUT;
}
return 0;
}
Would you like me to test this patch? If so, what should I apply it to
and how should I proceed?

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control
back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch"
for using the surround outputs even with these patches. As default,
it's set as "2ch".

Quoted 5 lines
Quoted 2 lines

Takashi

I will definitely try to give this a shot, but the outcome might be dependent on the fact whether Fedora 15 will want to work with 3.0-rc kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

Quoted 3 lines

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

Quoted 8 lines

You are right - when auto-mute is disabled sound goes via both speakers and headphones when they are plugged. I did not know the function of auto-mute.
However, the "Speaker" and "Headphone" controls still do influence both outputs, and "Speaker" can only be muted - there is no volume control available. So, in my opinion, they should either be merged altogether, or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that is setting the volume of speakers and headphones independently.

Quoted 2 lines

Give alsa-info.sh outputs on your machine with the latest status for further analysis.

I think this issue was fixed now in topic/hda branch in sound git tree:
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git

Quoted 8 lines
Quoted 5 lines

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

It seems like the problem is still there. The output of alsa-info.sh is available here:
http://www.alsa-project.org/db/?f=38e2e44ab86691006a837715601aad4311fda0d3

Double-check whether you compiled really the right stuff. The emulator works fine, so something wrong likely in your side.

Quoted 6 lines
Quoted 1 line

Takashi

I compiled the latest origin/master of sound-2.6 tree and the problem is still there. Output of alsa-info.sh is attached.

Julian

I had a closer look at 2.6.38.8-32.fc15.x86_64 and the controls are not completely separate. While you can regulate the volume of headphones and speakers separately, muting one mutes the other.

Julian

#27 lore raw

W dniu 29.06.2011 20:16, Julian Sikorski pisze:

Quoted 187 lines

W dniu 29.06.2011 19:36, Julian Sikorski pisze:

Quoted 186 lines

W dniu 28.06.2011 09:12, Takashi Iwai pisze:

Quoted 177 lines

At Mon, 27 Jun 2011 22:08:29 +0200,

Quoted 166 lines · Julian Sikorski

W dniu 27.06.2011 14:32, Takashi Iwai pisze:

Quoted 164 lines

At Mon, 27 Jun 2011 11:19:36 +0200,

Quoted 156 lines · Takashi Iwai

At Mon, 27 Jun 2011 08:21:26 +0200,

Quoted 144 lines · Julian Sikorski

W dniu 27.06.2011 08:04, Takashi Iwai pisze:

Quoted 138 lines

At Sat, 25 Jun 2011 14:01:06 +0200,

Quoted 128 lines · Julian Sikorski

W dniu 25.06.2011 13:31, Julian Sikorski pisze:

Quoted 126 lines

W dniu 25.06.2011 13:08, Julian Sikorski pisze:

Quoted 112 lines

W dniu 25.06.2011 09:11, Takashi Iwai pisze:

Quoted 102 lines

At Fri, 24 Jun 2011 13:25:53 +0200,

Quoted 97 lines · Julian Sikorski

On 24/06/2011 11:12, Takashi Iwai wrote:
At Fri, 24 Jun 2011 10:34:01 +0200,
Takashi Iwai wrote:

At Thu, 23 Jun 2011 18:40:47 +0200,
Julian Sikorski wrote:

On 23/06/2011 14:41, Takashi Iwai wrote:
At Thu, 23 Jun 2011 08:36:55 +0200,
Julian Sikorski wrote:

Hi,

I am coming here from pulseaudio-general mailing list [1]. I recently
got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in
microphone and the following connectors:
- headphone out
- microphone in; can be switched to center/lfe out
- spdif out; can be switched to rear speaker out
- line in; can be switched to side speaker out
Alsa does not seem to reflect that the device is capable of 5.1 and 7.1
sound, and there are two configs showing up in pavucontrol (analog
output and analog headphones) which seem to be the same. I have uploaded
the output of alsa-info.sh [2]. Please let me know if more information
is needed.

The current parser doesn't allow the multi-io pins when the primary
output is no line-out. The patch below should fix (change) the
behavior. It'll count HP out, too.

Takashi

---
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index fe56b2b..b0cf726 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
hda_nid_t dac;

spec->multiout.dac_nids = spec->private_dac_nids;
+ spec->multiout.num_dacs = 0;
for (i = 0; i< cfg->line_outs; i++) {
dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]);
if (!dac)
@@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
unsigned int location, defcfg;
int num_pins;

+ if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&& cfg->hp_outs == 1) {
+ /* use HP as primary out */
+ cfg->speaker_outs = cfg->line_outs;
+ memcpy(cfg->speaker_pins, cfg->line_out_pins,
+ sizeof(cfg->speaker_pins));
+ cfg->line_outs = cfg->hp_outs;
+ memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
+ cfg->hp_outs = 0;
+ memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+ cfg->line_out_type = AUTO_PIN_HP_OUT;
+ alc662_auto_fill_dac_nids(codec, cfg);
+ }
if (cfg->line_outs != 1 ||
- cfg->line_out_type != AUTO_PIN_LINE_OUT)
+ cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
return 0;

defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]);
@@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec)
spec->multi_ios = num_pins;
spec->ext_channel_count = 2;
spec->multiout.num_dacs = num_pins + 1;
+ /* for avoiding multi HP mixers */
+ cfg->line_out_type = AUTO_PIN_LINE_OUT;
}
return 0;
}
Would you like me to test this patch? If so, what should I apply it to
and how should I proceed?

Yes, the test would be appreciated, of course.
Apply it to the latest 3.0-rc kernel and test.

Also, the additional patch below will give "Headphone" mixer control
back while new "Surround", "Center" and "LFE" will appear.

Note that you'll need to change "Channel Mode" mixer control to "6ch"
for using the surround outputs even with these patches. As default,
it's set as "2ch".

Takashi

I will definitely try to give this a shot, but the outcome might be
dependent on the fact whether Fedora 15 will want to work with 3.0-rc
kernel.

You can build the kernel by yourself at any time...

Quoted 7 lines
Quoted 2 lines

How about 8-channel sound btw? Under Windows the device claims to be
capable of it.

Do you have 4 jacks? Otherwise it's nonsense.

Takashi

OK, I was able to successfully apply the patch and build the kernel. I tested it using:

Quoted 8 lines
$ pasuspender bash
$ speaker-test -Dplug:surround51 -c6
Once I set sound to 6-channel using alsamixer -c0, I was able to hear
the sound for all 6 channels. Setting it to 4 channels took away LFE and
center. Pulseaudio outputs are still a little messy, but this is out of
ALSA scope, I think.

Julian

It seems I spoke a bit too soon. The superfluous controls are still a problem. Speaker and Headphone controls seem to be overlapping (new output on amixer -c0 attached). They both control the headphones when they are plugged in and internal speakers when not.

Quoted 7 lines
Quoted 2 lines

Julian

Sorry for this email bombardment, but I just booted back to stock F15 kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone controls actually do what they advertise. Still, it is impossible to make the sound go through the speakers when headphones are plugged in (I tried pavucontrol for this).

Quoted 3 lines

The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. Set to "Disabled" will turn off the auto-mute in the driver side. However...

Quoted 8 lines

You are right - when auto-mute is disabled sound goes via both speakers and headphones when they are plugged. I did not know the function of auto-mute.
However, the "Speaker" and "Headphone" controls still do influence both outputs, and "Speaker" can only be muted - there is no volume control available. So, in my opinion, they should either be merged altogether, or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that is setting the volume of speakers and headphones independently.

Quoted 2 lines

Give alsa-info.sh outputs on your machine with the latest status for further analysis.

I think this issue was fixed now in topic/hda branch in sound git tree:
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git

Quoted 8 lines
Quoted 5 lines

Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc.

Takashi

It seems like the problem is still there. The output of alsa-info.sh is available here:
http://www.alsa-project.org/db/?f=38e2e44ab86691006a837715601aad4311fda0d3

Quoted 5 lines

Double-check whether you compiled really the right stuff. The emulator works fine, so something wrong likely in your side.

Takashi

I compiled the latest origin/master of sound-2.6 tree and the problem is still there. Output of alsa-info.sh is attached.

Quoted 7 lines
Quoted 2 lines

Julian

I had a closer look at 2.6.38.8-32.fc15.x86_64 and the controls are not completely separate. While you can regulate the volume of headphones and speakers separately, muting one mutes the other.

Julian

I also tried merging sound-2.6/master with Linus's tree, but this also did not help.

Julian

upload=true&script=true&cardinfo=
!!################################
!!ALSA Information Script v 0.4.60
!!################################

!!Script ran on: Wed Jun 29 19:20:56 UTC 2011

!!Linux Distribution
!!------------------

Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock)

!!DMI Information
!!---------------

Manufacturer:      CLEVO                            
Product Name:      P150HMx
Product Version:   Not Applicable                    

!!Kernel Information
!!------------------

Kernel release:    3.0-0.rc5.git0.1.belegdol3.fc15.x86_64
Operating System:  GNU/Linux
Architecture:      x86_64
Processor:         x86_64
SMP Enabled:       Yes

!!ALSA Version
!!------------

Driver version:     1.0.24
Library version:    1.0.24
Utilities version:  1.0.24.1

!!Loaded ALSA modules
!!-------------------

snd_hda_intel
snd_hda_intel

!!Sound Servers on this system
!!----------------------------

Pulseaudio:
Installed - Yes (/usr/bin/pulseaudio)
Running - Yes

Jack:
Installed - Yes (/usr/bin/jackd)
Running - No

!!Soundcards recognised by ALSA
!!-----------------------------

0 [PCH ]: HDA-Intel - HDA Intel PCH

                      HDA Intel PCH at 0xf6500000 irq 55
 1 [NVidia         ]: HDA-Intel - HDA NVidia
                      HDA NVidia at 0xf6080000 irq 17

!!PCI Soundcards installed in the system
!!--------------------------------------

00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 01:00.1 Audio device: nVidia Corporation Device 0beb (rev a1)

!!Advanced information - PCI Vendor/Device/Subsystem ID's !!--------------------------------------------------------

00:1b.0 0403: 8086:1c20 (rev 05)

	Subsystem: 1558:5102
--
01:00.1 0403: 10de:0beb (rev a1)
	Subsystem: 1558:5102

!!Loaded sound module options
!!--------------------------

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!HDA-Intel Codec information
!!---------------------------
--startcollapse--

Codec: Realtek ALC892
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0892
Subsystem Id: 0x15585102
Revision Id: 0x100302
No Modem Function Group found
Default PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Device: name="ALC892 Analog", type="Audio", device=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x40 0x40]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Surround Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x40 0x40]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Center Playback Volume", index=0, device=0

    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Volume", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x40 0x40]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x05 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0 Amp-Out vals: [0x40 0x40]
Converter: stream=0, channel=0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Control: name="IEC958 Default PCM Playback Switch", index=0, device=0
Device: name="ALC892 Digital", type="SPDIF", device=1
Converter: stream=5, channel=0
Digital: Enabled
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=1, device=0
Control: name="Capture Volume", index=1, device=0 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x90 0x90]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x23

Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=0, device=0
Control: name="Capture Volume", index=0, device=0
Device: name="ALC892 Analog", type="Audio", device=0 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x2e 0x2e]
Converter: stream=1, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x22

Node 0x0a [Audio Input] wcaps 0x100711: Stereo Digital
Converter: stream=0, channel=0
SDI-Select: 0
Digital:
Digital category: 0x0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x1f
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Internal Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Internal Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Line Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Control: name="Line Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
  Amp-In vals:  [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
  Connection: 10
     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17
Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Headphone Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x00 0x00]
  Connection: 2
     0x02 0x0b
Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Surround Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x80 0x80]
  Connection: 2
     0x03 0x0b
Node 0x0e [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Center Playback Switch", index=0, device=0
    ControlAmp: chs=1, dir=In, idx=0, ofs=0
  Control: name="LFE Playback Switch", index=0, device=0
    ControlAmp: chs=2, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x80 0x80]
  Connection: 2
     0x04 0x0b

Node 0x0f [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x05 0x0b

Node 0x10 [Audio Output] wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x11 [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x10

Node 0x12 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x0001003e: IN OUT HP EAPD Detect Trigger
  EAPD 0x2: EAPD
  Pin Default 0x99130110: [Fixed] Speaker at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x00:
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x0c

Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0d

Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0e

Node 0x17 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0f
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x03 0x03]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x01a11c30: [Jack] Mic at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0x0
  Pin-ctls: 0x21: IN VREF_50
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x19 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Internal Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x0000373e: IN OUT HP Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x99a30931: [Fixed] Mic at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x3, Sequence = 0x1
    Misc = NO_PRESENCE
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26

Node 0x1a [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00003736: IN OUT Detect Trigger

    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x0181143f: [Jack] Line In at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0xf
  Pin-ctls: 0x20: IN VREF_HIZ
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26

Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00]
Pincap 0x0001373e: IN OUT HP EAPD Detect Trigger

    Vref caps: HIZ 50 GRD 80 100
  EAPD 0x2: EAPD
  Pin Default 0x0121101f: [Jack] HP Out at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x1, Sequence = 0xf
  Pin-ctls: 0xc0: OUT HP VREF_HIZ
  Unsolicited: tag=04, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26

Node 0x1c [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x00000024: IN Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1d [Pin Complex] wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x598301f0: [N/A] Line In at Int ATAPI
Conn = ATAPI, Color = Unknown DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x01451120: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = Black DefAssociation = 0x2, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x06

Node 0x1f [Pin Complex] wcaps 0x400681: Stereo Digital
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=24
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=0, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x80 0x80] [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 12

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b 0x12

Node 0x23 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=1, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 11

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b

Node 0x24 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x25 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0 Amp-Out vals: [0x40 0x40]
Converter: stream=0, channel=0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x26 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x25 0x0b

Codec: Nvidia GPU 12 HDMI/DP
Address: 0
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=6, channel=0
Digital: Enabled GenLevel
Digital category: 0x2
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 1
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=2, device=0
Control: name="IEC958 Playback Pro Mask", index=2, device=0
Control: name="IEC958 Playback Default", index=2, device=0
Control: name="IEC958 Playback Switch", index=2, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 3
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=3, device=0
Control: name="IEC958 Playback Pro Mask", index=3, device=0
Control: name="IEC958 Playback Default", index=3, device=0
Control: name="IEC958 Playback Switch", index=3, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

--endcollapse--

!!ALSA Device nodes
!!-----------------

crw-rw----+ 1 root audio 116, 6 Jun 29 21:18 /dev/snd/controlC0 crw-rw----+ 1 root audio 116, 15 Jun 29 21:18 /dev/snd/controlC1 crw-rw----+ 1 root audio 116, 5 Jun 29 21:18 /dev/snd/hwC0D0 crw-rw----+ 1 root audio 116, 14 Jun 29 21:18 /dev/snd/hwC1D0 crw-rw----+ 1 root audio 116, 13 Jun 29 21:18 /dev/snd/hwC1D1 crw-rw----+ 1 root audio 116, 12 Jun 29 21:18 /dev/snd/hwC1D2 crw-rw----+ 1 root audio 116, 11 Jun 29 21:18 /dev/snd/hwC1D3

crw-rw----+ 1 root audio 116,  4 Jun 29 21:19 /dev/snd/pcmC0D0c
crw-rw----+ 1 root audio 116,  3 Jun 29 21:19 /dev/snd/pcmC0D0p
crw-rw----+ 1 root audio 116,  2 Jun 29 21:19 /dev/snd/pcmC0D1p
crw-rw----+ 1 root audio 116, 10 Jun 29 21:19 /dev/snd/pcmC1D3p
crw-rw----+ 1 root audio 116,  9 Jun 29 21:18 /dev/snd/pcmC1D7p
crw-rw----+ 1 root audio 116,  8 Jun 29 21:18 /dev/snd/pcmC1D8p
crw-rw----+ 1 root audio 116,  7 Jun 29 21:18 /dev/snd/pcmC1D9p
crw-rw----+ 1 root audio 116,  1 Jun 29 21:18 /dev/snd/seq

crw-rw----+ 1 root audio 116, 33 Jun 29 21:18 /dev/snd/timer

/dev/snd/by-path:
total 0
drwxr-xr-x. 2 root root 80 Jun 29 21:18 .
drwxr-xr-x. 3 root root 380 Jun 29 21:18 ..
lrwxrwxrwx. 1 root root 12 Jun 29 21:18 pci-0000:00:1b.0 -> ../controlC0 lrwxrwxrwx. 1 root root 12 Jun 29 21:18 pci-0000:01:00.1 -> ../controlC1

!!ALSA configuration files
!!------------------------

!!System wide config file (/etc/asound.conf)

#
# Place your global alsa-lib configuration here... #

@hooks [

	{
		func load
		files [
			"/etc/alsa/pulse-default.conf"
		]
		errors false
	}

]

!!Aplay/Arecord output
!!------------

APLAY

**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0

ARECORD

**** List of CAPTURE Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0

!!Amixer output
!!-------------

!!-------Mixer controls for card 0 [PCH]

Card hw:0 'PCH'/'HDA Intel PCH at 0xf6500000 irq 55'
Mixer name : 'Realtek ALC892'
Components : 'HDA:10ec0892,15585102,00100302'
Controls : 33
Simple ctrls : 20
Simple mixer control 'Master',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Headphone',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Speaker',0
Capabilities: pswitch penum
Playback channels: Front Left - Front Right
Mono:
Front Left: Playback [on]
Front Right: Playback [on]
Simple mixer control 'PCM',0
Capabilities: pvolume penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 255 [100%] [0.00dB]
Front Right: Playback 255 [100%] [0.00dB]
Simple mixer control 'Surround',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Center',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'LFE',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Line',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 3 [100%] [30.00dB]
Front Right: 3 [100%] [30.00dB]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958 Default PCM',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 46 [100%] [30.00dB] [on]
Front Right: Capture 46 [100%] [30.00dB] [on]
Simple mixer control 'Capture',1
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 16 [35%] [0.00dB] [off]
Front Right: Capture 16 [35%] [0.00dB] [off]
Simple mixer control 'Auto-Mute Mode',0
Capabilities: enum
Items: 'Disabled' 'Enabled'
Item0: 'Enabled'
Simple mixer control 'Channel Mode',0
Capabilities: enum
Items: '2ch' '4ch' '6ch'
Item0: '2ch'
Simple mixer control 'Input Source',0
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Internal Mic'
Simple mixer control 'Input Source',1
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Mic'
Simple mixer control 'Internal Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Internal Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]

!!-------Mixer controls for card 1 [NVidia]

Card hw:1 'NVidia'/'HDA NVidia at 0xf6080000 irq 17'
Mixer name : 'Nvidia GPU 12 HDMI/DP'
Components : 'HDA:10de0012,10de0101,00100100'
Controls : 16
Simple ctrls : 4
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958',1
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',2
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',3
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]

!!Alsactl output
!!-------------

--startcollapse--

state.PCH {
	control.1 {
		iface MIXER
		name 'Channel Mode'
		value '2ch'
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 '2ch'
			item.1 '4ch'
			item.2 '6ch'
		}
	}
	control.2 {
		iface MIXER
		name 'Headphone Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.3 {
		iface MIXER
		name 'Headphone Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.4 {
		iface MIXER
		name 'Surround Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.5 {
		iface MIXER
		name 'Surround Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.6 {
		iface MIXER
		name 'Center Playback Volume'
		value 64
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
		}
	}
	control.7 {
		iface MIXER
		name 'LFE Playback Volume'
		value 64
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
		}
	}
	control.8 {
		iface MIXER
		name 'Center Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'LFE Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'Speaker Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.11 {
		iface MIXER
		name 'Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.12 {
		iface MIXER
		name 'Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.13 {
		iface MIXER
		name 'Internal Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.14 {
		iface MIXER
		name 'Internal Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.15 {
		iface MIXER
		name 'Line Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.16 {
		iface MIXER
		name 'Line Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.17 {
		iface MIXER
		name 'Mic Boost Volume'
		value.0 3
		value.1 3
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 3000
			dbvalue.1 3000
		}
	}
	control.18 {
		iface MIXER
		name 'Internal Mic Boost Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.19 {
		iface MIXER
		name 'Auto-Mute Mode'
		value Enabled
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Disabled
			item.1 Enabled
		}
	}
	control.20 {
		iface MIXER
		name 'Capture Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.21 {
		iface MIXER
		name 'Capture Switch'
		index 1
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.22 {
		iface MIXER
		name 'Capture Volume'
		value.0 46
		value.1 46
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 3000
			dbvalue.1 3000
		}
	}
	control.23 {
		iface MIXER
		name 'Capture Volume'
		index 1
		value.0 16
		value.1 16
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.24 {
		iface MIXER
		name 'Input Source'
		value 'Internal Mic'
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.25 {
		iface MIXER
		name 'Input Source'
		index 1
		value Mic
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.26 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.27 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.28 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.29 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.30 {
		iface MIXER
		name 'IEC958 Default PCM Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.31 {
		iface MIXER
		name 'Master Playback Volume'
		value 64
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
		}
	}
	control.32 {
		iface MIXER
		name 'Master Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.33 {
		iface MIXER
		name 'PCM Playback Volume'
		value.0 255
		value.1 255
		comment {
			access 'read write user'
			type INTEGER
			count 2
			range '0 - 255'
			tlv '0000000100000008ffffec1400000014'
			dbmin -5100
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
}
state.NVidia {
	control.1 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.2 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.3 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.4 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.5 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 1
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.6 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 1
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.7 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 1
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.8 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 1
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 2
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 2
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.11 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 2
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.12 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 2
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.13 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 3
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.14 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 3
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.15 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 3
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.16 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 3
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
}

--endcollapse--

!!All Loaded Modules
!!------------------

Module
ebtable_nat
ebtables
ipt_MASQUERADE
iptable_nat
nf_nat
xt_CHECKSUM
iptable_mangle
bridge
stp
llc
sunrpc
cpufreq_ondemand
acpi_cpufreq
freq_table
mperf
bnep
bluetooth
ip6t_REJECT
nf_conntrack_ipv6
nf_conntrack_ipv4
nf_defrag_ipv6
nf_defrag_ipv4
xt_state
nf_conntrack
ip6table_filter
ip6_tables
fuse
arc4
snd_hda_codec_hdmi
uvcvideo
videodev
media
v4l2_compat_ioctl32
microcode
snd_hda_codec_realtek
joydev
iwlagn
serio_raw
mac80211
cfg80211
iTCO_wdt
snd_hda_intel
i2c_i801
iTCO_vendor_support
i2c_core
rfkill
snd_hda_codec
snd_hwdep
snd_seq
snd_seq_device
xhci_hcd
jme
snd_pcm
jmb38x_ms
memstick
mii
snd_timer
snd
soundcore
snd_page_alloc
virtio_net
kvm_intel
kvm
firewire_ohci
firewire_core
crc_itu_t
sdhci_pci
sdhci
mmc_core
wmi
video

!!Sysfs Files
!!-----------

/sys/class/sound/hwC0D0/init_pin_configs:
0x11 0x411111f0
0x12 0x411111f0
0x14 0x99130110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x411111f0
0x18 0x01a11c30
0x19 0x99a30931
0x1a 0x0181143f
0x1b 0x0121101f
0x1c 0x411111f0
0x1d 0x598301f0
0x1e 0x01451120
0x1f 0x411111f0

/sys/class/sound/hwC0D0/driver_pin_configs:

/sys/class/sound/hwC0D0/user_pin_configs:

/sys/class/sound/hwC0D0/init_verbs:

/sys/class/sound/hwC1D0/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D0/driver_pin_configs:

/sys/class/sound/hwC1D0/user_pin_configs:

/sys/class/sound/hwC1D0/init_verbs:

/sys/class/sound/hwC1D1/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D1/driver_pin_configs:

/sys/class/sound/hwC1D1/user_pin_configs:

/sys/class/sound/hwC1D1/init_verbs:

/sys/class/sound/hwC1D2/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D2/driver_pin_configs:

/sys/class/sound/hwC1D2/user_pin_configs:

/sys/class/sound/hwC1D2/init_verbs:

/sys/class/sound/hwC1D3/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D3/driver_pin_configs:

/sys/class/sound/hwC1D3/user_pin_configs:

/sys/class/sound/hwC1D3/init_verbs:

!!ALSA/HDA dmesg
!!------------------

[   19.234472] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[   19.239261] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   19.239428] snd_hda_intel 0000:00:1b.0: irq 55 for MSI/MSI-X
[   19.239536] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[   19.244616] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
--
[   19.351725] mtp-probe[615]: bus: 1, device: 3 was not an MTP device
[   19.353115] hda_codec: ALC892: SKU not ready 0x598301f0
[   19.353287] hda_codec: ALC892: BIOS auto-probing.
[   19.353298] ALSA sound/pci/hda/hda_codec.c:4799 autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   19.353304] ALSA sound/pci/hda/hda_codec.c:4803    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   19.353310] ALSA sound/pci/hda/hda_codec.c:4807    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   19.353314] ALSA sound/pci/hda/hda_codec.c:4808    mono: mono_out=0x0
[   19.353318] ALSA sound/pci/hda/hda_codec.c:4811    dig-out=0x1e/0x0
[   19.353322] ALSA sound/pci/hda/hda_codec.c:4812    inputs:
[   19.353327] ALSA sound/pci/hda/hda_codec.c:4816  Mic=0x18
[   19.353331] ALSA sound/pci/hda/hda_codec.c:4816  Internal Mic=0x19
[   19.353333] ALSA sound/pci/hda/hda_codec.c:4816  Line=0x1a
[   19.353336] ALSA sound/pci/hda/hda_codec.c:4818 
[   19.354836] ALSA sound/pci/hda/patch_realtek.c:1799 realtek: No valid SSID, checking pincfg 0x598301f0 for NID 0x1d
[   19.354840] ALSA sound/pci/hda/patch_realtek.c:1880 realtek: Enable default setup for auto mode as fallback
[   19.397617] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   19.399587] microcode: CPU0 sig=0x206a7, pf=0x10, revision=0x14
--
[   19.399980] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[   19.433294] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   19.433308] hda_intel: Disabling MSI
[   19.433571] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[   19.441890] ALSA sound/pci/hda/hda_intel.c:1454 Enable delay in RIRB handling
[   19.506458] mtp-probe[689]: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5"
--
[   19.689284] USB Video Class driver (v1.1.0)
[   19.716930] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
[   19.756819] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0
[   19.796768] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0
[   19.817243] cfg80211: World regulatory domain updated:
--
[   19.829519] microcode: CPU7 updated to revision 0x17, date = 2011-04-07
[   19.837751] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[   19.868962] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input12
[   19.869902] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13
[   19.870624] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[   19.871728] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[   19.919928] udev[516]: renamed network interface eth0 to p34p1
--
[   42.099000] wlan0: no IPv6 routers present
[   84.818146] hda-intel: Invalid position buffer, using LPIB read method instead.
[   85.212411] hda-intel: Invalid position buffer, using LPIB read method instead.
[   85.817501] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
[  169.487784] iwlagn 0000:04:00.0: Aggregation not enabled for tid 0 because load = 1
#28 lore raw

At Wed, 29 Jun 2011 21:29:38 +0200,

Quoted 3 lines · Julian Sikorski

I also tried merging sound-2.6/master with Linus's tree, but this also did not help.

It's really strange. Are you sure that this is the kernel you modified properly? Before further debugging, check two things:

- Run "git log sound/pci/hda/patch_realtek.c" and the first few entries, whether they come from sound git tree. For example, check the commit below is contained:

commit 7ec9c6ccc6007b14a916021d4ba7ffbcc7822ae3
Author: Takashi Iwai <[email protected]>
Date: Mon Jun 27 15:53:38 2011 +0200

ALSA: hda - Fix volume-init for ALC259 with invalid widget caps

- Confirm the running kernel is what you really built and installed. You can modify the suffix via $CONFIG_LOCALVERSION in .config file. Name it uniquely, rebuild, re-install and reboot. The new suffix should appear in the output of "uname -r".

- Once when these are correct, check /proc/asound/card0/codec#0:
the widget NID 0x02 should contain "Speaker Playback Volume" instead of "Headphone Playback Volume" with the latest driver.

Takashi

#29 lore raw

W dniu 30.06.2011 07:26, Takashi Iwai pisze:

Quoted 13 lines

At Wed, 29 Jun 2011 21:29:38 +0200,

Quoted 3 lines · Julian Sikorski

I also tried merging sound-2.6/master with Linus's tree, but this also did not help.

It's really strange. Are you sure that this is the kernel you modified properly? Before further debugging, check two things:

- Run "git log sound/pci/hda/patch_realtek.c" and the first few entries, whether they come from sound git tree. For example, check the commit below is contained:

Quoted 5 lines

commit 7ec9c6ccc6007b14a916021d4ba7ffbcc7822ae3
Author: Takashi Iwai <[email protected]>
Date: Mon Jun 27 15:53:38 2011 +0200

ALSA: hda - Fix volume-init for ALC259 with invalid widget caps

commit 0b0c8490670a77b937f502491ae9d5236aa4054a

Author: Takashi Iwai <[email protected]>
Date:   Tue Jun 28 12:45:47 2011 +0200

ALSA: hda - Create snd_hda_get_conn_index() helper function

Create snd_hda_get_conn_index() helper function for obtaining the connection index of the widget. Replaced the similar codes used in several codec-drivers with this common helper.

commit 4f574b7b1a1cc8aac617e938459e8f03a641e678

Author: Takashi Iwai <[email protected]>
Date:   Mon Jun 27 16:17:07 2011 +0200

ALSA: hda - More volume-init fixes for ALC267 codec

More similar fixes like previous commits: handle the exceptional case like ALC267 where no volume amp is found in ADC widget but in the capsrc widget instead.

Also minor checks for avoiding possible erros: no connection-select when the pin has a single selection, and add beep verbs only when the 0x1d is used for beep.

To be even more sure, I re-synced your branch again and built a new kernel. The patch_realtek.c file being built is here:
http://belegdol.fedorapeople.org/patch_realtek.c
Fresh alsa-info.sh is here:
http://www.alsa-project.org/db/?f=5051b2cb788b1db4273e06e98a78783dd0ec679f

Quoted 5 lines

- Confirm the running kernel is what you really built and installed. You can modify the suffix via $CONFIG_LOCALVERSION in .config file. Name it uniquely, rebuild, re-install and reboot. The new suffix should appear in the output of "uname -r".

belegdol4 is the suffix I added:

$ uname -r
3.0-0.rc5.git0.1.belegdol4.fc15.x86_64
Quoted 3 lines

- Once when these are correct, check /proc/asound/card0/codec#0:
the widget NID 0x02 should contain "Speaker Playback Volume" instead of "Headphone Playback Volume" with the latest driver.

Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

Perhaps I need to specify a correct model to enable this code?

Quoted 1 line

Takashi

Julian

#31 lore raw
In reply to a message not in the archive

At Thu, 30 Jun 2011 08:30:10 +0200,

Quoted 47 lines · Julian Sikorski

W dniu 30.06.2011 07:26, Takashi Iwai pisze:

Quoted 13 lines

At Wed, 29 Jun 2011 21:29:38 +0200,

Quoted 3 lines · Julian Sikorski

I also tried merging sound-2.6/master with Linus's tree, but this also did not help.

It's really strange. Are you sure that this is the kernel you modified properly? Before further debugging, check two things:

- Run "git log sound/pci/hda/patch_realtek.c" and the first few entries, whether they come from sound git tree. For example, check the commit below is contained:

Quoted 5 lines

commit 7ec9c6ccc6007b14a916021d4ba7ffbcc7822ae3
Author: Takashi Iwai <[email protected]>
Date: Mon Jun 27 15:53:38 2011 +0200

ALSA: hda - Fix volume-init for ALC259 with invalid widget caps

commit 0b0c8490670a77b937f502491ae9d5236aa4054a

Author: Takashi Iwai <[email protected]>
Date:   Tue Jun 28 12:45:47 2011 +0200

ALSA: hda - Create snd_hda_get_conn_index() helper function

Create snd_hda_get_conn_index() helper function for obtaining the connection index of the widget. Replaced the similar codes used in several codec-drivers with this common helper.

commit 4f574b7b1a1cc8aac617e938459e8f03a641e678

Author: Takashi Iwai <[email protected]>
Date:   Mon Jun 27 16:17:07 2011 +0200

ALSA: hda - More volume-init fixes for ALC267 codec

More similar fixes like previous commits: handle the exceptional case like ALC267 where no volume amp is found in ADC widget but in the capsrc widget instead.

Also minor checks for avoiding possible erros: no connection-select when the pin has a single selection, and add beep verbs only when the 0x1d is used for beep.

Quoted 6 lines

To be even more sure, I re-synced your branch again and built a new kernel. I am attaching patch_realtek.c file being built. Fresh alsa-info.sh is here:
http://www.alsa-project.org/db/?f=5051b2cb788b1db4273e06e98a78783dd0ec679f

OK, then it's correct.

Quoted 10 lines
Quoted 5 lines

- Confirm the running kernel is what you really built and installed. You can modify the suffix via $CONFIG_LOCALVERSION in .config file. Name it uniquely, rebuild, re-install and reboot. The new suffix should appear in the output of "uname -r".

belegdol4 is the suffix I added:

$ uname -r
3.0-0.rc5.git0.1.belegdol4.fc15.x86_64
Quoted 8 lines
Quoted 3 lines

- Once when these are correct, check /proc/asound/card0/codec#0:
the widget NID 0x02 should contain "Speaker Playback Volume" instead of "Headphone Playback Volume" with the latest driver.

Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

Perhaps I need to specify a correct model to enable this code?

No, you shouldn't pass any model option.

Could you apply the patch below to add some debug prints, and give the relevant kernel messages you get? Just grep lines with 'XXX'.

Takashi

---

sound/pci/hda/patch_realtek.c +19 -1
index 7b96dce..3134555 100644
@@ -18770,8 +18770,10 @@ static hda_nid_t alc_auto_look_for_dac(struct hda_codec *codec, hda_nid_t pin)
 static hda_nid_t get_dac_if_single(struct hda_codec *codec, hda_nid_t pin)
 {
 	hda_nid_t sel = alc_go_down_to_selector(codec, pin);
-	if (snd_hda_get_conn_list(codec, sel, NULL) == 1)
+	if (snd_hda_get_conn_list(codec, sel, NULL) == 1) {
+		printk(KERN_DEBUG "XXX pin %x coupled with a single DAC\n", pin);
 		return alc_auto_look_for_dac(codec, pin);
+	}
 	return 0;
 }
 
@@ -18783,6 +18785,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec)
 	bool redone;
 	int i;
 
+	printk(KERN_DEBUG "XXX alc662_auto_fill_dac_nids called\n");
  again:
 	spec->multiout.num_dacs = 0;
 	spec->multiout.hp_nid = 0;
@@ -18813,6 +18816,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec)
 			 * checking the hard-wired DACs
 			 */
 			redone = true;
+			printk(KERN_DEBUG "XXX redoing...\n");
 			goto again;
 		}
 	}
@@ -18826,6 +18830,17 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec)
 				sizeof(hda_nid_t) * (cfg->line_outs - i - 1));
 	}
 
+	printk(KERN_DEBUG "XXX filled dacs: %x/%x/%x/%x/%x, hp %x, ext %x/%x/%x\n",
+	       spec->private_dac_nids[0],
+	       spec->private_dac_nids[1],
+	       spec->private_dac_nids[2],
+	       spec->private_dac_nids[3],
+	       spec->private_dac_nids[4],
+	       spec->multiout.hp_nid,
+	       spec->multiout.extra_out_nid[0],
+	       spec->multiout.extra_out_nid[1],
+	       spec->multiout.extra_out_nid[2]);
+
 	return 0;
 }
 
@@ -18877,6 +18892,7 @@ static int alc662_auto_create_multi_out_ctls(struct hda_codec *codec,
 		mix = alc_auto_dac_to_mix(codec, pin, nid);
 		if (!mix)
 			continue;
+		printk(KERN_DEBUG "XXX create mixer ch %d pin %x dac %x mix %x\n", i, pin, nid, mix);
 		name = alc_get_line_out_pfx(spec, i, true, &index);
 		if (!name) {
 			/* Center/LFE */
@@ -19026,6 +19042,7 @@ static int alc_auto_fill_multi_ios(struct hda_codec *codec,
 			dac = alc_auto_look_for_dac(codec, nid);
 			if (!dac)
 				continue;
+			printk(KERN_DEBUG "XXX added multi-io pin %x, dac %x\n", nid, dac);
 			spec->multi_io[num_pins].pin = nid;
 			spec->multi_io[num_pins].dac = dac;
 			num_pins++;
@@ -19128,6 +19145,7 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec,
 
 	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT && cfg->hp_outs == 1) {
 		/* use HP as primary out */
+		printk(KERN_DEBUG "XXX swap primary out to HP\n");
 		cfg->speaker_outs = cfg->line_outs;
 		memcpy(cfg->speaker_pins, cfg->line_out_pins,
 		       sizeof(cfg->speaker_pins));
#32 lore raw

W dniu 30.06.2011 08:54, Takashi Iwai pisze:

Quoted 77 lines

At Thu, 30 Jun 2011 08:30:10 +0200,

Quoted 47 lines · Julian Sikorski

W dniu 30.06.2011 07:26, Takashi Iwai pisze:

Quoted 13 lines

At Wed, 29 Jun 2011 21:29:38 +0200,

Quoted 3 lines · Julian Sikorski

I also tried merging sound-2.6/master with Linus's tree, but this also did not help.

It's really strange. Are you sure that this is the kernel you modified properly? Before further debugging, check two things:

- Run "git log sound/pci/hda/patch_realtek.c" and the first few entries, whether they come from sound git tree. For example, check the commit below is contained:

Quoted 5 lines

commit 7ec9c6ccc6007b14a916021d4ba7ffbcc7822ae3
Author: Takashi Iwai <[email protected]>
Date: Mon Jun 27 15:53:38 2011 +0200

ALSA: hda - Fix volume-init for ALC259 with invalid widget caps

commit 0b0c8490670a77b937f502491ae9d5236aa4054a

Author: Takashi Iwai <[email protected]>
Date:   Tue Jun 28 12:45:47 2011 +0200

ALSA: hda - Create snd_hda_get_conn_index() helper function

Create snd_hda_get_conn_index() helper function for obtaining the connection index of the widget. Replaced the similar codes used in several codec-drivers with this common helper.

commit 4f574b7b1a1cc8aac617e938459e8f03a641e678

Author: Takashi Iwai <[email protected]>
Date:   Mon Jun 27 16:17:07 2011 +0200

ALSA: hda - More volume-init fixes for ALC267 codec

More similar fixes like previous commits: handle the exceptional case like ALC267 where no volume amp is found in ADC widget but in the capsrc widget instead.

Also minor checks for avoiding possible erros: no connection-select when the pin has a single selection, and add beep verbs only when the 0x1d is used for beep.

Quoted 6 lines

To be even more sure, I re-synced your branch again and built a new kernel. I am attaching patch_realtek.c file being built. Fresh alsa-info.sh is here:
http://www.alsa-project.org/db/?f=5051b2cb788b1db4273e06e98a78783dd0ec679f

OK, then it's correct.

Quoted 10 lines
Quoted 5 lines

- Confirm the running kernel is what you really built and installed. You can modify the suffix via $CONFIG_LOCALVERSION in .config file. Name it uniquely, rebuild, re-install and reboot. The new suffix should appear in the output of "uname -r".

belegdol4 is the suffix I added:

$ uname -r
3.0-0.rc5.git0.1.belegdol4.fc15.x86_64
Quoted 8 lines
Quoted 3 lines

- Once when these are correct, check /proc/asound/card0/codec#0:
the widget NID 0x02 should contain "Speaker Playback Volume" instead of "Headphone Playback Volume" with the latest driver.

Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

Perhaps I need to specify a correct model to enable this code?

Quoted 7 lines

No, you shouldn't pass any model option.

Could you apply the patch below to add some debug prints, and give the relevant kernel messages you get? Just grep lines with 'XXX'.

Takashi

Here you go:

$ dmesg | grep XXX
[   12.789557] XXX alc662_auto_fill_dac_nids called
[   12.789716] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   12.789718] XXX swap primary out to HP
[   12.789719] XXX alc662_auto_fill_dac_nids called
[   12.789845] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   12.790094] XXX added multi-io pin 1a, dac 3
[   12.790343] XXX added multi-io pin 18, dac 4
[   12.790347] XXX create mixer ch 0 pin 1b dac 2 mix c
[   12.790351] XXX create mixer ch 1 pin 1a dac 3 mix d
[   12.790354] XXX create mixer ch 2 pin 18 dac 4 mix e

Julian

#33 lore raw

At Thu, 30 Jun 2011 19:00:44 +0200,

Quoted 87 lines · Julian Sikorski

W dniu 30.06.2011 08:54, Takashi Iwai pisze:

Quoted 77 lines

At Thu, 30 Jun 2011 08:30:10 +0200,

Quoted 47 lines · Julian Sikorski

W dniu 30.06.2011 07:26, Takashi Iwai pisze:

Quoted 13 lines

At Wed, 29 Jun 2011 21:29:38 +0200,

Quoted 3 lines · Julian Sikorski

I also tried merging sound-2.6/master with Linus's tree, but this also did not help.

It's really strange. Are you sure that this is the kernel you modified properly? Before further debugging, check two things:

- Run "git log sound/pci/hda/patch_realtek.c" and the first few entries, whether they come from sound git tree. For example, check the commit below is contained:

Quoted 5 lines

commit 7ec9c6ccc6007b14a916021d4ba7ffbcc7822ae3
Author: Takashi Iwai <[email protected]>
Date: Mon Jun 27 15:53:38 2011 +0200

ALSA: hda - Fix volume-init for ALC259 with invalid widget caps

commit 0b0c8490670a77b937f502491ae9d5236aa4054a

Author: Takashi Iwai <[email protected]>
Date:   Tue Jun 28 12:45:47 2011 +0200

ALSA: hda - Create snd_hda_get_conn_index() helper function

Create snd_hda_get_conn_index() helper function for obtaining the connection index of the widget. Replaced the similar codes used in several codec-drivers with this common helper.

commit 4f574b7b1a1cc8aac617e938459e8f03a641e678

Author: Takashi Iwai <[email protected]>
Date:   Mon Jun 27 16:17:07 2011 +0200

ALSA: hda - More volume-init fixes for ALC267 codec

More similar fixes like previous commits: handle the exceptional case like ALC267 where no volume amp is found in ADC widget but in the capsrc widget instead.

Also minor checks for avoiding possible erros: no connection-select when the pin has a single selection, and add beep verbs only when the 0x1d is used for beep.

Quoted 6 lines

To be even more sure, I re-synced your branch again and built a new kernel. I am attaching patch_realtek.c file being built. Fresh alsa-info.sh is here:
http://www.alsa-project.org/db/?f=5051b2cb788b1db4273e06e98a78783dd0ec679f

OK, then it's correct.

Quoted 10 lines
Quoted 5 lines

- Confirm the running kernel is what you really built and installed. You can modify the suffix via $CONFIG_LOCALVERSION in .config file. Name it uniquely, rebuild, re-install and reboot. The new suffix should appear in the output of "uname -r".

belegdol4 is the suffix I added:

$ uname -r
3.0-0.rc5.git0.1.belegdol4.fc15.x86_64
Quoted 8 lines
Quoted 3 lines

- Once when these are correct, check /proc/asound/card0/codec#0:
the widget NID 0x02 should contain "Speaker Playback Volume" instead of "Headphone Playback Volume" with the latest driver.

Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

Perhaps I need to specify a correct model to enable this code?

Quoted 7 lines

No, you shouldn't pass any model option.

Could you apply the patch below to add some debug prints, and give the relevant kernel messages you get? Just grep lines with 'XXX'.

Takashi

Quoted 8 lines

Here you go:

$ dmesg | grep XXX
[   12.789557] XXX alc662_auto_fill_dac_nids called
[   12.789716] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   12.789718] XXX swap primary out to HP
[   12.789719] XXX alc662_auto_fill_dac_nids called
[   12.789845] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0

OK, at this point, something is wrong.

Could you try the patch again (after reverting the previous debug patch)? This will give a bit more outputs.

I have a vague idea what could be wrong now. Maybe the connection list is differently returned from the real hardware unlike the emulator. But I need to see it in more details.

thanks,

Takashi

---

sound/pci/hda/patch_realtek.c +28 -1
index 7b96dce..0a28371 100644
@@ -18770,8 +18770,11 @@ static hda_nid_t alc_auto_look_for_dac(struct hda_codec *codec, hda_nid_t pin)
 static hda_nid_t get_dac_if_single(struct hda_codec *codec, hda_nid_t pin)
 {
 	hda_nid_t sel = alc_go_down_to_selector(codec, pin);
-	if (snd_hda_get_conn_list(codec, sel, NULL) == 1)
+	printk(KERN_DEBUG "XXX check single for pin %x, sel %x\n", pin, sel);
+	if (snd_hda_get_conn_list(codec, sel, NULL) == 1) {
+		printk(KERN_DEBUG "XXX pin %x coupled with a single DAC\n", pin);
 		return alc_auto_look_for_dac(codec, pin);
+	}
 	return 0;
 }
 
@@ -18783,6 +18786,13 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec)
 	bool redone;
 	int i;
 
+	printk(KERN_DEBUG "XXX alc662_auto_fill_dac_nids called\n");
+	printk(KERN_DEBUG "XXX line_outs=%d, %x/%x/%x\n",
+	       cfg->line_outs, cfg->line_out_pins[0], cfg->line_out_pins[1], cfg->line_out_pins[2]);
+	printk(KERN_DEBUG "XXX hp_outs=%d, %x/%x/%x\n",
+	       cfg->hp_outs, cfg->hp_pins[0], cfg->hp_pins[1], cfg->hp_pins[2]);
+	printk(KERN_DEBUG "XXX spk_outs=%d, %x/%x/%x\n",
+	       cfg->speaker_outs, cfg->speaker_pins[0], cfg->speaker_pins[1], cfg->speaker_pins[2]);
  again:
 	spec->multiout.num_dacs = 0;
 	spec->multiout.hp_nid = 0;
@@ -18813,6 +18823,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec)
 			 * checking the hard-wired DACs
 			 */
 			redone = true;
+			printk(KERN_DEBUG "XXX redoing...\n");
 			goto again;
 		}
 	}
@@ -18826,6 +18837,17 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec)
 				sizeof(hda_nid_t) * (cfg->line_outs - i - 1));
 	}
 
+	printk(KERN_DEBUG "XXX filled dacs: %x/%x/%x/%x/%x, hp %x, ext %x/%x/%x\n",
+	       spec->private_dac_nids[0],
+	       spec->private_dac_nids[1],
+	       spec->private_dac_nids[2],
+	       spec->private_dac_nids[3],
+	       spec->private_dac_nids[4],
+	       spec->multiout.hp_nid,
+	       spec->multiout.extra_out_nid[0],
+	       spec->multiout.extra_out_nid[1],
+	       spec->multiout.extra_out_nid[2]);
+
 	return 0;
 }
 
@@ -18877,6 +18899,7 @@ static int alc662_auto_create_multi_out_ctls(struct hda_codec *codec,
 		mix = alc_auto_dac_to_mix(codec, pin, nid);
 		if (!mix)
 			continue;
+		printk(KERN_DEBUG "XXX create mixer ch %d pin %x dac %x mix %x\n", i, pin, nid, mix);
 		name = alc_get_line_out_pfx(spec, i, true, &index);
 		if (!name) {
 			/* Center/LFE */
@@ -19026,6 +19049,7 @@ static int alc_auto_fill_multi_ios(struct hda_codec *codec,
 			dac = alc_auto_look_for_dac(codec, nid);
 			if (!dac)
 				continue;
+			printk(KERN_DEBUG "XXX added multi-io pin %x, dac %x\n", nid, dac);
 			spec->multi_io[num_pins].pin = nid;
 			spec->multi_io[num_pins].dac = dac;
 			num_pins++;
@@ -19128,13 +19152,16 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec,
 
 	if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT && cfg->hp_outs == 1) {
 		/* use HP as primary out */
+		printk(KERN_DEBUG "XXX swap primary out to HP\n");
 		cfg->speaker_outs = cfg->line_outs;
 		memcpy(cfg->speaker_pins, cfg->line_out_pins,
 		       sizeof(cfg->speaker_pins));
+		printk(KERN_DEBUG "XXX spk=%x\n", cfg->speaker_pins[0]);
 		cfg->line_outs = cfg->hp_outs;
 		memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins));
 		cfg->hp_outs = 0;
 		memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins));
+		printk(KERN_DEBUG "XXX line=%x\n", cfg->line_out_pins[0]);
 		cfg->line_out_type = AUTO_PIN_HP_OUT;
 		if (fill_dac)
 			fill_dac(codec);
#34 lore raw

W dniu 30.06.2011 19:41, Takashi Iwai pisze:

Quoted 103 lines

At Thu, 30 Jun 2011 19:00:44 +0200,

Quoted 87 lines · Julian Sikorski

W dniu 30.06.2011 08:54, Takashi Iwai pisze:

Quoted 77 lines

At Thu, 30 Jun 2011 08:30:10 +0200,

Quoted 47 lines · Julian Sikorski

W dniu 30.06.2011 07:26, Takashi Iwai pisze:

Quoted 13 lines

At Wed, 29 Jun 2011 21:29:38 +0200,

Quoted 3 lines · Julian Sikorski

I also tried merging sound-2.6/master with Linus's tree, but this also did not help.

It's really strange. Are you sure that this is the kernel you modified properly? Before further debugging, check two things:

- Run "git log sound/pci/hda/patch_realtek.c" and the first few entries, whether they come from sound git tree. For example, check the commit below is contained:

Quoted 5 lines

commit 7ec9c6ccc6007b14a916021d4ba7ffbcc7822ae3
Author: Takashi Iwai <[email protected]>
Date: Mon Jun 27 15:53:38 2011 +0200

ALSA: hda - Fix volume-init for ALC259 with invalid widget caps

commit 0b0c8490670a77b937f502491ae9d5236aa4054a

Author: Takashi Iwai <[email protected]>
Date:   Tue Jun 28 12:45:47 2011 +0200

ALSA: hda - Create snd_hda_get_conn_index() helper function

Create snd_hda_get_conn_index() helper function for obtaining the connection index of the widget. Replaced the similar codes used in several codec-drivers with this common helper.

commit 4f574b7b1a1cc8aac617e938459e8f03a641e678

Author: Takashi Iwai <[email protected]>
Date:   Mon Jun 27 16:17:07 2011 +0200

ALSA: hda - More volume-init fixes for ALC267 codec

More similar fixes like previous commits: handle the exceptional case like ALC267 where no volume amp is found in ADC widget but in the capsrc widget instead.

Also minor checks for avoiding possible erros: no connection-select when the pin has a single selection, and add beep verbs only when the 0x1d is used for beep.

Quoted 6 lines

To be even more sure, I re-synced your branch again and built a new kernel. I am attaching patch_realtek.c file being built. Fresh alsa-info.sh is here:
http://www.alsa-project.org/db/?f=5051b2cb788b1db4273e06e98a78783dd0ec679f

OK, then it's correct.

Quoted 10 lines
Quoted 5 lines

- Confirm the running kernel is what you really built and installed. You can modify the suffix via $CONFIG_LOCALVERSION in .config file. Name it uniquely, rebuild, re-install and reboot. The new suffix should appear in the output of "uname -r".

belegdol4 is the suffix I added:

$ uname -r
3.0-0.rc5.git0.1.belegdol4.fc15.x86_64
Quoted 8 lines
Quoted 3 lines

- Once when these are correct, check /proc/asound/card0/codec#0:
the widget NID 0x02 should contain "Speaker Playback Volume" instead of "Headphone Playback Volume" with the latest driver.

Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

Perhaps I need to specify a correct model to enable this code?

Quoted 7 lines

No, you shouldn't pass any model option.

Could you apply the patch below to add some debug prints, and give the relevant kernel messages you get? Just grep lines with 'XXX'.

Takashi

Quoted 8 lines

Here you go:

$ dmesg | grep XXX
[   12.789557] XXX alc662_auto_fill_dac_nids called
[   12.789716] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   12.789718] XXX swap primary out to HP
[   12.789719] XXX alc662_auto_fill_dac_nids called
[   12.789845] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0

OK, at this point, something is wrong.

Could you try the patch again (after reverting the previous debug patch)? This will give a bit more outputs.

Quoted 8 lines

I have a vague idea what could be wrong now. Maybe the connection list is differently returned from the real hardware unlike the emulator. But I need to see it in more details.

thanks,

Takashi

No problem:

$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e

Julian

#35 lore raw

At Thu, 30 Jun 2011 20:09:49 +0200,

Quoted 12 lines · Julian Sikorski
$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
Quoted 8 lines
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e

How about the fix below?

Takashi

---

sound/pci/hda/patch_realtek.c +1 -1
index 7b96dce..757a8a3 100644
@@ -18780,7 +18780,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec)
 {
 	struct alc_spec *spec = codec->spec;
 	const struct auto_pin_cfg *cfg = &spec->autocfg;
-	bool redone;
+	bool redone = false;
 	int i;
 
  again:
#36 lore raw

W dniu 30.06.2011 21:28, Takashi Iwai pisze:

Quoted 23 lines

At Thu, 30 Jun 2011 20:09:49 +0200,

Quoted 12 lines · Julian Sikorski
$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
Quoted 8 lines
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e
Quoted 4 lines

How about the fix below?

Takashi

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

$ dmesg | grep XXX
[   13.944531] XXX alc662_auto_fill_dac_nids called
[   13.944533] XXX line_outs=1, 14/0/0
[   13.944534] XXX hp_outs=1, 1b/0/0
[   13.944536] XXX spk_outs=0, 0/0/0
[   13.944631] XXX check single for pin 14, sel 14
[   13.944632] XXX pin 14 coupled with a single DAC
[   13.944843] XXX check single for pin 1b, sel 1b
[   13.944845] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   13.944847] XXX swap primary out to HP
[   13.944848] XXX spk=14
[   13.944849] XXX line=1b
[   13.944850] XXX alc662_auto_fill_dac_nids called
[   13.944852] XXX line_outs=1, 1b/0/0
[   13.944853] XXX hp_outs=0, 0/0/0
[   13.944855] XXX spk_outs=1, 14/0/0
[   13.944856] XXX check single for pin 1b, sel 1b
[   13.944858] XXX check single for pin 14, sel 14
[   13.944859] XXX pin 14 coupled with a single DAC
[   13.944945] XXX filled dacs: 3/0/0/0/0, hp 0, ext 2/0/0
[   13.945189] XXX added multi-io pin 1a, dac 4
[   13.945440] XXX added multi-io pin 18, dac 5
[   13.945446] XXX create mixer ch 0 pin 1b dac 3 mix d
[   13.945452] XXX create mixer ch 1 pin 1a dac 4 mix e
[   13.945457] XXX create mixer ch 2 pin 18 dac 5 mix f

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.
Thanks for all the help so far,

Julian

#37 lore raw

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 28 lines · Julian Sikorski

W dniu 30.06.2011 21:28, Takashi Iwai pisze:

Quoted 26 lines

At Thu, 30 Jun 2011 20:09:49 +0200,

Quoted 12 lines · Julian Sikorski
$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
Quoted 8 lines
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e

How about the fix below?

Quoted 7 lines
Quoted 1 line

Takashi

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

Quoted 2 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

thanks,

Takashi

#38 lore raw

W dniu 01.07.2011 07:21, Takashi Iwai pisze:

Quoted 38 lines

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 28 lines · Julian Sikorski

W dniu 30.06.2011 21:28, Takashi Iwai pisze:

Quoted 26 lines

At Thu, 30 Jun 2011 20:09:49 +0200,

Quoted 12 lines · Julian Sikorski
$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
Quoted 8 lines
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e

How about the fix below?

Quoted 7 lines
Quoted 1 line

Takashi

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Quoted 3 lines

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

I assume that the auto-mute function uses a different approach then - it disables the speakers sound when headphone jack is plugged in.

Quoted 5 lines
Quoted 2 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

I see. I can try updating the BIOS and see if it changes anything. If it doesn't, is there a way to work the problem around in the driver?

Quoted 3 lines

thanks,

Takashi

Cheers,
Julian

#39 lore raw

At Fri, 01 Jul 2011 08:14:26 +0200,

Quoted 40 lines · Julian Sikorski

W dniu 01.07.2011 07:21, Takashi Iwai pisze:

Quoted 38 lines

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 35 lines · Julian Sikorski

W dniu 30.06.2011 21:28, Takashi Iwai pisze:

Quoted 23 lines

At Thu, 30 Jun 2011 20:09:49 +0200,

Quoted 12 lines · Julian Sikorski
$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
Quoted 8 lines
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e
Quoted 4 lines

How about the fix below?

Takashi

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Quoted 6 lines
Quoted 3 lines

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

I assume that the auto-mute function uses a different approach then - it disables the speakers sound when headphone jack is plugged in.

Yes, it changes the pin-control value.

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

I see. I can try updating the BIOS and see if it changes anything. If it doesn't, is there a way to work the problem around in the driver?

You need to figure out pins manually by yourself, then change the driver code. I leave it as a homework :)

thanks,

Takashi

#40 lore raw

W dniu 01.07.2011 08:24, Takashi Iwai pisze:

Quoted 42 lines

At Fri, 01 Jul 2011 08:14:26 +0200,

Quoted 40 lines · Julian Sikorski

W dniu 01.07.2011 07:21, Takashi Iwai pisze:

Quoted 38 lines

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 35 lines · Julian Sikorski

W dniu 30.06.2011 21:28, Takashi Iwai pisze:

Quoted 23 lines

At Thu, 30 Jun 2011 20:09:49 +0200,

Quoted 12 lines · Julian Sikorski
$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
Quoted 8 lines
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e
Quoted 4 lines

How about the fix below?

Takashi

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

I assume that the auto-mute function uses a different approach then - it disables the speakers sound when headphone jack is plugged in.

Yes, it changes the pin-control value.

Thanks for clarification.

Quoted 11 lines
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

I see. I can try updating the BIOS and see if it changes anything. If it doesn't, is there a way to work the problem around in the driver?

You need to figure out pins manually by yourself, then change the driver code. I leave it as a homework :)

:) I cannot write code, so I would not count on myself doing that. I will have a look into updating the BIOS though.

Quoted 3 lines

thanks,

Takashi

Once again thanks for all the work you have done,

Julian

#41 lore raw

W dniu 01.07.2011 08:27, Julian Sikorski pisze:

Quoted 69 lines

W dniu 01.07.2011 08:24, Takashi Iwai pisze:

Quoted 42 lines

At Fri, 01 Jul 2011 08:14:26 +0200,

Quoted 40 lines · Julian Sikorski

W dniu 01.07.2011 07:21, Takashi Iwai pisze:

Quoted 38 lines

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 35 lines · Julian Sikorski

W dniu 30.06.2011 21:28, Takashi Iwai pisze:

Quoted 23 lines

At Thu, 30 Jun 2011 20:09:49 +0200,

Quoted 12 lines · Julian Sikorski
$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
Quoted 8 lines
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e
Quoted 4 lines

How about the fix below?

Takashi

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

I assume that the auto-mute function uses a different approach then - it disables the speakers sound when headphone jack is plugged in.

Yes, it changes the pin-control value.

Thanks for clarification.

Quoted 11 lines
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

I see. I can try updating the BIOS and see if it changes anything. If it doesn't, is there a way to work the problem around in the driver?

You need to figure out pins manually by yourself, then change the driver code. I leave it as a homework :)

:) I cannot write code, so I would not count on myself doing that. I will have a look into updating the BIOS though.

Quoted 7 lines
Quoted 3 lines

thanks,

Takashi

Once again thanks for all the work you have done,

Julian

Hmm, I googled a bit and it seems the way to find the pins is to write values to user_pin_configs. So no coding knowledge seems needed, could you give me some pointers on where to start?

Thanks,
Julian

#42 lore raw

At Fri, 01 Jul 2011 09:07:47 +0200,

Quoted 18 lines · Julian Sikorski
Quoted 18 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 3 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

I see. I can try updating the BIOS and see if it changes anything. If it doesn't, is there a way to work the problem around in the driver?

You need to figure out pins manually by yourself, then change the driver code. I leave it as a homework :)

:) I cannot write code, so I would not count on myself doing that. I will have a look into updating the BIOS though.

Quoted 2 lines

thanks,

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

Takashi

Once again thanks for all the work you have done,

Julian

Hmm, I googled a bit and it seems the way to find the pins is to write values to user_pin_configs. So no coding knowledge seems needed, could you give me some pointers on where to start?

First off, read the HD-audio specification to understand what the values represent. Then, use hda-analyzer or manually via hda-verb, figure out which widget corresponds to which I/O jack. Compose the corresponding pin-config value, and put it to the sysfs file. A brief description is found in Documentation/sound/alsa/HD-Audio.txt.

Takashi

#48 lore raw
In reply to Takashi Iwai

At Fri, 01 Jul 2011 07:21:34 +0200,

Quoted 10 lines · Takashi Iwai

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 6 lines · Julian Sikorski

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Quoted 3 lines

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

I seem to have lied. It should be possible, and the emulator shows it must be working well.

Do I understand correctly that the problem is that both HP and speaker outputs are muted simultaneously when you either of "Headphone" or "Speaker" mixer switch is muted?

If so, please give alsa-info.sh outputs at the problematic state, i.e. the speaker gets muted by the headphone mixer switch or vice versa, just to confirm.

thanks,

Takashi

#43 lore raw
In reply to Takashi Iwai
Quoted 29 lines · Takashi Iwai

At Fri, 01 Jul 2011 09:07:47 +0200,

Quoted 18 lines · Julian Sikorski
Quoted 18 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 3 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

I see. I can try updating the BIOS and see if it changes anything. If it doesn't, is there a way to work the problem around in the driver?

You need to figure out pins manually by yourself, then change the driver code. I leave it as a homework :)

:) I cannot write code, so I would not count on myself doing that. I will have a look into updating the BIOS though.

Quoted 2 lines

thanks,

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

Takashi

Once again thanks for all the work you have done,

Julian

Hmm, I googled a bit and it seems the way to find the pins is to write values to user_pin_configs. So no coding knowledge seems needed, could you give me some pointers on where to start?

Quoted 8 lines

First off, read the HD-audio specification to understand what the values represent. Then, use hda-analyzer or manually via hda-verb, figure out which widget corresponds to which I/O jack. Compose the corresponding pin-config value, and put it to the sysfs file. A brief description is found in Documentation/sound/alsa/HD-Audio.txt.

Takashi

I was reading a bit more and it is all very confusing, but luckily I have holidays coming to try and figure it out. In the meantime, should I also try to find the pin for the internal subwoofer?
WRT the alsa-info.sh output I'll send it once I get home later today.

Julian

#49 lore raw
In reply to Takashi Iwai

W dniu 01.07.2011 09:32, Takashi Iwai pisze:

Quoted 23 lines

At Fri, 01 Jul 2011 07:21:34 +0200,

Quoted 10 lines · Takashi Iwai

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 6 lines · Julian Sikorski

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Quoted 3 lines

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

I seem to have lied. It should be possible, and the emulator shows it must be working well.

Do I understand correctly that the problem is that both HP and speaker outputs are muted simultaneously when you either of "Headphone" or "Speaker" mixer switch is muted?

Quoted 8 lines

If so, please give alsa-info.sh outputs at the problematic state, i.e. the speaker gets muted by the headphone mixer switch or vice versa, just to confirm.

thanks,

Takashi

Here you go:
http://www.alsa-project.org/db/?f=c8f1e149c155ed950aea1a7327a5800fc2b61da2
I muted the speakers and the headphones went silent.

Julian

#50 lore raw

At Fri, 01 Jul 2011 20:57:23 +0200,

Quoted 30 lines · Julian Sikorski

W dniu 01.07.2011 09:32, Takashi Iwai pisze:

Quoted 28 lines

At Fri, 01 Jul 2011 07:21:34 +0200,

Quoted 10 lines · Takashi Iwai

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 6 lines · Julian Sikorski

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Quoted 3 lines

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

I seem to have lied. It should be possible, and the emulator shows it must be working well.

Do I understand correctly that the problem is that both HP and speaker outputs are muted simultaneously when you either of "Headphone" or "Speaker" mixer switch is muted?

If so, please give alsa-info.sh outputs at the problematic state, i.e. the speaker gets muted by the headphone mixer switch or vice versa, just to confirm.

Quoted 6 lines
Quoted 3 lines

thanks,

Takashi

Here you go:
http://www.alsa-project.org/db/?f=c8f1e149c155ed950aea1a7327a5800fc2b61da2
I muted the speakers and the headphones went silent.

Hm, I see no obvious problem in the codec tree and alsa mixers. Could you check whether the playback without PulseAudio has the same issue? Try pasuspender, e.g.

% pasuspender aplay -Dplughw foo.wav

(Depending on the version of PA, you might need to put '--' between
pasuspender and aplay.)

Takashi

#51 lore raw

W dniu 01.07.2011 21:25, Takashi Iwai pisze:

Quoted 43 lines

At Fri, 01 Jul 2011 20:57:23 +0200,

Quoted 30 lines · Julian Sikorski

W dniu 01.07.2011 09:32, Takashi Iwai pisze:

Quoted 28 lines

At Fri, 01 Jul 2011 07:21:34 +0200,

Quoted 10 lines · Takashi Iwai

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 6 lines · Julian Sikorski

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Quoted 3 lines

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

I seem to have lied. It should be possible, and the emulator shows it must be working well.

Do I understand correctly that the problem is that both HP and speaker outputs are muted simultaneously when you either of "Headphone" or "Speaker" mixer switch is muted?

If so, please give alsa-info.sh outputs at the problematic state, i.e. the speaker gets muted by the headphone mixer switch or vice versa, just to confirm.

Quoted 6 lines
Quoted 3 lines

thanks,

Takashi

Here you go:
http://www.alsa-project.org/db/?f=c8f1e149c155ed950aea1a7327a5800fc2b61da2
I muted the speakers and the headphones went silent.

Hm, I see no obvious problem in the codec tree and alsa mixers. Could you check whether the playback without PulseAudio has the same issue? Try pasuspender, e.g.

Quoted 7 lines

% pasuspender aplay -Dplughw foo.wav

(Depending on the version of PA, you might need to put '--' between
pasuspender and aplay.)

Takashi

You are right, with pulseaudio out of the way everything works fine. Anything particular I should tell them?

Julian

#44 lore raw
In reply to Takashi Iwai

W dniu 01.07.2011 09:14, Takashi Iwai pisze:

Quoted 29 lines

At Fri, 01 Jul 2011 09:07:47 +0200,

Quoted 18 lines · Julian Sikorski
Quoted 18 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 3 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

I see. I can try updating the BIOS and see if it changes anything. If it doesn't, is there a way to work the problem around in the driver?

You need to figure out pins manually by yourself, then change the driver code. I leave it as a homework :)

:) I cannot write code, so I would not count on myself doing that. I will have a look into updating the BIOS though.

Quoted 2 lines

thanks,

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

Takashi

Once again thanks for all the work you have done,

Julian

Hmm, I googled a bit and it seems the way to find the pins is to write values to user_pin_configs. So no coding knowledge seems needed, could you give me some pointers on where to start?

Quoted 8 lines

First off, read the HD-audio specification to understand what the values represent. Then, use hda-analyzer or manually via hda-verb, figure out which widget corresponds to which I/O jack. Compose the corresponding pin-config value, and put it to the sysfs file. A brief description is found in Documentation/sound/alsa/HD-Audio.txt.

Takashi

I have been scratching my head for almost 2 h now without much progress. Can I steal this values from Windows driver somehow? It seems to be possible:

http://www.insanelymac.com/forum/index.php?s=3298551705d0d48ba8faa28b9a7d3283&showtopic=137188&st=20

Julian

#45 lore raw

W dniu 2011-07-02 00:09, Julian Sikorski pisze:

Quoted 37 lines

W dniu 01.07.2011 09:14, Takashi Iwai pisze:

Quoted 36 lines

At Fri, 01 Jul 2011 09:07:47 +0200,

Quoted 18 lines · Julian Sikorski
Quoted 18 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 3 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

I see. I can try updating the BIOS and see if it changes anything. If it doesn't, is there a way to work the problem around in the driver?

You need to figure out pins manually by yourself, then change the driver code. I leave it as a homework :)

:) I cannot write code, so I would not count on myself doing that. I will have a look into updating the BIOS though.

Quoted 2 lines

thanks,

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

Takashi

Once again thanks for all the work you have done,

Julian

Hmm, I googled a bit and it seems the way to find the pins is to write values to user_pin_configs. So no coding knowledge seems needed, could you give me some pointers on where to start?

First off, read the HD-audio specification to understand what the values represent. Then, use hda-analyzer or manually via hda-verb, figure out which widget corresponds to which I/O jack. Compose the corresponding pin-config value, and put it to the sysfs file. A brief description is found in Documentation/sound/alsa/HD-Audio.txt.

Quoted 8 lines
Quoted 1 line

Takashi

I have been scratching my head for almost 2 h now without much progress. Can I steal this values from Windows driver somehow? It seems to be possible:

http://www.insanelymac.com/forum/index.php?s=3298551705d0d48ba8faa28b9a7d3283&showtopic=137188&st=20

Julian

I managed to get the data out of Windows install, does it look useful?

Julian

Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Class\{4D36E96C-E325-11CE-BFC1-08002BE10318}\0000\PinConfigOverrideVerbs] "0000"=hex:f0,1c,17,01
"0001"=hex:11,1d,17,01
"0002"=hex:11,1e,17,01
"0003"=hex:41,1f,17,01
"0004"=hex:f0,1c,27,01
"0005"=hex:11,1d,27,01
"0006"=hex:11,1e,27,01
"0007"=hex:41,1f,27,01
"0008"=hex:10,1c,47,01
"0009"=hex:01,1d,47,01
"0010"=hex:13,1e,47,01
"0011"=hex:99,1f,47,01
"0012"=hex:f0,1c,57,01
"0013"=hex:11,1d,57,01
"0014"=hex:11,1e,57,01
"0015"=hex:41,1f,57,01
"0016"=hex:f0,1c,67,01
"0017"=hex:11,1d,67,01
"0018"=hex:11,1e,67,01
"0019"=hex:41,1f,67,01
"0020"=hex:f0,1c,77,01
"0021"=hex:11,1d,77,01
"0022"=hex:11,1e,77,01
"0023"=hex:41,1f,77,01
"0024"=hex:30,1c,87,01
"0025"=hex:1c,1d,87,01
"0026"=hex:a1,1e,87,01
"0027"=hex:01,1f,87,01
"0028"=hex:31,1c,97,01
"0029"=hex:09,1d,97,01
"0030"=hex:a3,1e,97,01
"0031"=hex:99,1f,97,01
"0032"=hex:3f,1c,a7,01
"0033"=hex:14,1d,a7,01
"0034"=hex:81,1e,a7,01
"0035"=hex:01,1f,a7,01
"0036"=hex:1f,1c,b7,01
"0037"=hex:10,1d,b7,01
"0038"=hex:21,1e,b7,01
"0039"=hex:01,1f,b7,01
"0040"=hex:f0,1c,c7,01
"0041"=hex:11,1d,c7,01
"0042"=hex:11,1e,c7,01
"0043"=hex:41,1f,c7,01
"0044"=hex:f0,1c,d7,01
"0045"=hex:01,1d,d7,01
"0046"=hex:83,1e,d7,01
"0047"=hex:59,1f,d7,01
"0048"=hex:20,1c,e7,01
"0049"=hex:11,1d,e7,01
"0050"=hex:45,1e,e7,01
"0051"=hex:01,1f,e7,01
"0052"=hex:f0,1c,f7,01
"0053"=hex:11,1d,f7,01
"0054"=hex:11,1e,f7,01
"0055"=hex:41,1f,f7,01
"NumVerbs"=hex:38,00,00,00

#52 lore raw
In reply to Takashi Iwai

W dniu 01.07.2011 07:21, Takashi Iwai pisze:

Quoted 45 lines

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 28 lines · Julian Sikorski

W dniu 30.06.2011 21:28, Takashi Iwai pisze:

Quoted 26 lines

At Thu, 30 Jun 2011 20:09:49 +0200,

Quoted 12 lines · Julian Sikorski
$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
Quoted 8 lines
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e

How about the fix below?

Quoted 7 lines
Quoted 1 line

Takashi

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

Quoted 2 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

Quoted 7 lines

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

thanks,

Takashi

FYI I updated the BIOS to the latest available version, but it does not seem to have changed anything. New alsa-info.sh output:
http://www.alsa-project.org/db/?f=89e03c194e599829e132517342cce70133f3fc7a

Julian

#46 lore raw
In reply to Julian Sikorski

W dniu 02.07.2011 00:37, Julian Sikorski pisze:

Quoted 45 lines

W dniu 2011-07-02 00:09, Julian Sikorski pisze:

Quoted 44 lines

W dniu 01.07.2011 09:14, Takashi Iwai pisze:

Quoted 31 lines

At Fri, 01 Jul 2011 09:07:47 +0200,

Quoted 20 lines · Julian Sikorski
Quoted 20 lines
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
Quoted 4 lines

So it seems that the only things remaining are the SPDIF/rear channel
jack and the coupled muting issue.

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

Quoted 6 lines
Quoted 3 lines

I see. I can try updating the BIOS and see if it changes anything. If it
doesn't, is there a way to work the problem around in the driver?

You need to figure out pins manually by yourself, then change the driver code. I leave it as a homework :)

:) I cannot write code, so I would not count on myself doing that. I will have a look into updating the BIOS though.

Quoted 2 lines

thanks,

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

Takashi

Once again thanks for all the work you have done,

Julian

Hmm, I googled a bit and it seems the way to find the pins is to write values to user_pin_configs. So no coding knowledge seems needed, could you give me some pointers on where to start?

Quoted 8 lines

First off, read the HD-audio specification to understand what the values represent. Then, use hda-analyzer or manually via hda-verb, figure out which widget corresponds to which I/O jack. Compose the corresponding pin-config value, and put it to the sysfs file. A brief description is found in Documentation/sound/alsa/HD-Audio.txt.

Takashi

I have been scratching my head for almost 2 h now without much progress. Can I steal this values from Windows driver somehow? It seems to be possible:

Quoted 8 lines
Quoted 4 lines

http://www.insanelymac.com/forum/index.php?s=3298551705d0d48ba8faa28b9a7d3283&showtopic=137188&st=20

Julian

I managed to get the data out of Windows install, does it look useful?

Julian

I managed to figure out which ini file is used for my device, I am attaching both the 32- and 64-bit versions. Hopefully there is some useful info inside.

Julian

#53 lore raw
In reply to Takashi Iwai

W dniu 01.07.2011 07:21, Takashi Iwai pisze:

Quoted 7 lines

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

thanks,

Takashi

I finally managed to figure out what these numbers mean. But then I got confused by your statement:

$ cat /sys/class/sound/card0/hwC0D0/init_pin_configs
0x11 0x411111f0
0x12 0x411111f0
0x14 0x99130110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x411111f0
0x18 0x01a11c30
0x19 0x99a30931
0x1a 0x0181143f
0x1b 0x0121101f
0x1c 0x411111f0
0x1d 0x598301f0
0x1e 0x01451120
0x1f 0x411111f0
Quoted 1 line

From what I was able to decipher, 0x1e is a jack, external rear, with

spdif out default output and optical connection. It is black. The same physical socket is used for the last 2 surround channels. Could you please clarify? Thanks in advance.

Julian

#54 lore raw

2011/7/5 Julian Sikorski <[email protected]>:

Quoted 4 lines

From what I was able to decipher, 0x1e is a jack, external rear, with spdif out default output and optical connection. It is black. The same physical socket is used for the last 2 surround channels. Could you please clarify? Thanks in advance.

Take a look at Block Diagram of alc892 datasheet

http://www.realtek.com/products/productsView.aspx?Langid=1&PNid=24&PFid=28&Level=5&Conn=4&ProdID=284

if you can confirmed the internal mic, mic jack ,line in , line out and internal speaker work as expected

the only pin complex which can be connected to rear [Audio Output] 0x0d is 0x15

seem that the pin complex for 4 jack 8-ch notebook are different from desktop with 6 jacks at rear panel

a 10 channel codec is able to provide volume control for internal speaker and 4 jacks

#68 lore raw
In reply to Julian Sikorski

At Tue, 05 Jul 2011 00:50:43 +0200,

Quoted 28 lines · Julian Sikorski

W dniu 01.07.2011 07:21, Takashi Iwai pisze:

Quoted 7 lines

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

thanks,

Takashi

I finally managed to figure out what these numbers mean. But then I got confused by your statement:

$ cat /sys/class/sound/card0/hwC0D0/init_pin_configs
0x11 0x411111f0
0x12 0x411111f0
0x14 0x99130110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x411111f0
0x18 0x01a11c30
0x19 0x99a30931
0x1a 0x0181143f
0x1b 0x0121101f
0x1c 0x411111f0
0x1d 0x598301f0
0x1e 0x01451120
0x1f 0x411111f0
Quoted 4 lines
Quoted 1 line

From what I was able to decipher, 0x1e is a jack, external rear, with

spdif out default output and optical connection. It is black. The same physical socket is used for the last 2 surround channels. Could you please clarify? Thanks in advance.

Two jacks shares the same place, but it doesn't mean that they share the physical connection. SPDIF is optical and the surround is mini-jack. Usually they are implemented in different pins, but placed to a single position.

Takashi

#55 lore raw
In reply to Raymond Yau

W dniu 05.07.2011 03:31, Raymond Yau pisze:

Quoted 14 lines

2011/7/5 Julian Sikorski <[email protected]>:

Quoted 4 lines

From what I was able to decipher, 0x1e is a jack, external rear, with spdif out default output and optical connection. It is black. The same physical socket is used for the last 2 surround channels. Could you please clarify? Thanks in advance.

Take a look at Block Diagram of alc892 datasheet

http://www.realtek.com/products/productsView.aspx?Langid=1&PNid=24&PFid=28&Level=5&Conn=4&ProdID=284

if you can confirmed the internal mic, mic jack ,line in , line out and internal speaker work as expected

Quoted 7 lines

the only pin complex which can be connected to rear [Audio Output] 0x0d is 0x15

seem that the pin complex for 4 jack 8-ch notebook are different from desktop with 6 jacks at rear panel

a 10 channel codec is able to provide volume control for internal speaker and 4 jacks

I have tested int speakers, int mic, ext mic, line in, hp jack, lfe/center and rear surround. All seem to work. The only thing untested is the optical out.

Julian

#47 lore raw
In reply to Takashi Iwai

W dniu 01.07.2011 08:24, Takashi Iwai pisze:

Quoted 60 lines

At Fri, 01 Jul 2011 08:14:26 +0200,

Quoted 40 lines · Julian Sikorski

W dniu 01.07.2011 07:21, Takashi Iwai pisze:

Quoted 38 lines

At Thu, 30 Jun 2011 22:16:04 +0200,

Quoted 35 lines · Julian Sikorski

W dniu 30.06.2011 21:28, Takashi Iwai pisze:

Quoted 23 lines

At Thu, 30 Jun 2011 20:09:49 +0200,

Quoted 12 lines · Julian Sikorski
$ dmesg | grep XXX
[   14.813013] XXX alc662_auto_fill_dac_nids called
[   14.813015] XXX line_outs=1, 14/0/0
[   14.813016] XXX hp_outs=1, 1b/0/0
[   14.813018] XXX spk_outs=0, 0/0/0
[   14.813186] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813187] XXX swap primary out to HP
[   14.813188] XXX spk=14
[   14.813190] XXX line=1b
[   14.813191] XXX alc662_auto_fill_dac_nids called
[   14.813192] XXX line_outs=1, 1b/0/0
Quoted 8 lines
[   14.813194] XXX hp_outs=0, 0/0/0
[   14.813195] XXX spk_outs=1, 14/0/0
[   14.813311] XXX filled dacs: 2/0/0/0/0, hp 0, ext 0/0/0
[   14.813560] XXX added multi-io pin 1a, dac 3
[   14.813814] XXX added multi-io pin 18, dac 4
[   14.813818] XXX create mixer ch 0 pin 1b dac 2 mix c
[   14.813821] XXX create mixer ch 1 pin 1a dac 3 mix d
[   14.813825] XXX create mixer ch 2 pin 18 dac 4 mix e
Quoted 4 lines

How about the fix below?

Takashi

It works, thanks! In more detail, the Speaker/Headphone situation is back to 2.6.38 state - you can regulate them independently, but muting one mutes the other. LFE/Center and Surround keep working correctly too. The new output of alsa-info.sh:
http://www.alsa-project.org/db/?f=45bc0df9747371b348bde6c4aa508b2ba44aff47

Quoted 6 lines
Quoted 3 lines

Right, it's because ALC892 has no mute-control in pin widgets but only in the mixer widget. And HP and speaker paths share the same mixer, thus it's impossible to mute independently.

I assume that the auto-mute function uses a different approach then - it disables the speakers sound when headphone jack is plugged in.

Yes, it changes the pin-control value.

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

So it seems that the only things remaining are the SPDIF/rear channel jack and the coupled muting issue.

It's a BIOS bug. It doesn't tell SPDIF is available. Ditto for the 4th stereo out. No pin is exposed by BIOS.

I see. I can try updating the BIOS and see if it changes anything. If it doesn't, is there a way to work the problem around in the driver?

Quoted 7 lines

You need to figure out pins manually by yourself, then change the driver code. I leave it as a homework :)

thanks,

Takashi

I have figured out part of the value I need to assign: a black 1/8'' jack for speakers, rear external, will be 0x01111xxx.
I am having hard time figuring out the last 3 numbers:
- only the last one of misc bits is defined in the spec (jack sensing override), yet the bios test it to values > 0001 for some of my jacks
- the default association and sequence seem to have more choices, should I steal these from other pin configs to make it work with 8-channel sound?

Julian

#56 lore raw
In reply to Raymond Yau

W dniu 05.07.2011 03:31, Raymond Yau pisze:

Quoted 14 lines

2011/7/5 Julian Sikorski<[email protected]>:

Quoted 4 lines

From what I was able to decipher, 0x1e is a jack, external rear, with
spdif out default output and optical connection. It is black. The same physical socket is used for the last 2 surround channels. Could you please clarify? Thanks in advance.

Take a look at Block Diagram of alc892 datasheet

http://www.realtek.com/products/productsView.aspx?Langid=1&PNid=24&PFid=28&Level=5&Conn=4&ProdID=284

if you can confirmed the internal mic, mic jack ,line in , line out and internal speaker work as expected

Quoted 7 lines

the only pin complex which can be connected to rear [Audio Output] 0x0d is 0x15

seem that the pin complex for 4 jack 8-ch notebook are different from desktop with 6 jacks at rear panel

a 10 channel codec is able to provide volume control for internal speaker and 4 jacks

Thanks to Raymond's advice I was finally able to make the sound come out of the copper part of the spdif/side surround jack. I am pasting the diff created with hda-analyzer, please let me know if this gives you enough information to add proper 7.1 sound support for this laptop. Here is the alsa-info.sh with all jacks playing sound:
http://www.alsa-project.org/db/?f=8f23e499727ec612ed925b81d3f38928e8f6aebb
Of course, there is still no specific volume control for the side channel.

Julian

Diff for codec 0/0 (0x10ec0892):
---
+++
@@ -223,23 +223,23 @@

      Misc = NO_PRESENCE
    Pin-ctls: 0x20: IN
    Unsolicited: tag=0x00, enabled=0
    Power: setting=D0, actual=D0
    Connection: 1
       0x0e
  Node 0x17 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
    Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
-  Amp-Out vals: [0x80 0x80]
+  Amp-Out vals: [0x00 0x00]
    Pincap 0x00000036: IN OUT Detect Trigger
    Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
      Conn = 1/8, Color = Black
      DefAssociation = 0xf, Sequence = 0x0
      Misc = NO_PRESENCE
-  Pin-ctls: 0x20: IN
+  Pin-ctls: 0x40: OUT
    Unsolicited: tag=0x00, enabled=0
    Power: setting=D0, actual=D0
    Connection: 1
       0x0f

Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Control: name="Center Playback Switch", index=0, device=0
ControlAmp: chs=1, dir=1, idx=0, ofs=0
Control: name="LFE Playback Switch", index=0, device=

#57 lore raw

W dniu 17.07.2011 13:55, Julian Sikorski pisze:

Quoted 33 lines

W dniu 05.07.2011 03:31, Raymond Yau pisze:

Quoted 15 lines

2011/7/5 Julian Sikorski<[email protected]>:

Quoted 4 lines

From what I was able to decipher, 0x1e is a jack, external rear, with spdif out default output and optical connection. It is black. The same physical socket is used for the last 2 surround channels. Could you please clarify? Thanks in advance.

Take a look at Block Diagram of alc892 datasheet

http://www.realtek.com/products/productsView.aspx?Langid=1&PNid=24&PFid=28&Level=5&Conn=4&ProdID=284

if you can confirmed the internal mic, mic jack ,line in , line out and internal speaker work as expected

Quoted 8 lines

the only pin complex which can be connected to rear [Audio Output] 0x0d is 0x15

seem that the pin complex for 4 jack 8-ch notebook are different from desktop with 6 jacks at rear panel

a 10 channel codec is able to provide volume control for internal speaker and 4 jacks

Thanks to Raymond's advice I was finally able to make the sound come out of the copper part of the spdif/side surround jack. I am pasting the diff created with hda-analyzer, please let me know if this gives you enough information to add proper 7.1 sound support for this laptop. Here is the alsa-info.sh with all jacks playing sound:
http://www.alsa-project.org/db/?f=8f23e499727ec612ed925b81d3f38928e8f6aebb
Of course, there is still no specific volume control for the side channel.

Quoted 2 lines

Julian

Upon further investigation I discovered that with the volume on the 0x17 can be controlled with center/lfe in alsamixer. I don't think it is the intended behaviour.

Julian

Julian

#58 lore raw

At Sun, 17 Jul 2011 14:17:22 +0200,

Quoted 35 lines · Julian Sikorski

W dniu 17.07.2011 13:55, Julian Sikorski pisze:

Quoted 33 lines

W dniu 05.07.2011 03:31, Raymond Yau pisze:

Quoted 15 lines

2011/7/5 Julian Sikorski<[email protected]>:

Quoted 4 lines

From what I was able to decipher, 0x1e is a jack, external rear, with spdif out default output and optical connection. It is black. The same physical socket is used for the last 2 surround channels. Could you please clarify? Thanks in advance.

Take a look at Block Diagram of alc892 datasheet

http://www.realtek.com/products/productsView.aspx?Langid=1&PNid=24&PFid=28&Level=5&Conn=4&ProdID=284

if you can confirmed the internal mic, mic jack ,line in , line out and internal speaker work as expected

Quoted 8 lines

the only pin complex which can be connected to rear [Audio Output] 0x0d is 0x15

seem that the pin complex for 4 jack 8-ch notebook are different from desktop with 6 jacks at rear panel

a 10 channel codec is able to provide volume control for internal speaker and 4 jacks

Thanks to Raymond's advice I was finally able to make the sound come out of the copper part of the spdif/side surround jack. I am pasting the diff created with hda-analyzer, please let me know if this gives you enough information to add proper 7.1 sound support for this laptop. Here is the alsa-info.sh with all jacks playing sound:
http://www.alsa-project.org/db/?f=8f23e499727ec612ed925b81d3f38928e8f6aebb
Of course, there is still no specific volume control for the side channel.

Quoted 6 lines
Quoted 2 lines

Julian

Upon further investigation I discovered that with the volume on the 0x17 can be controlled with center/lfe in alsamixer. I don't think it is the intended behaviour.

Is it with the very latest alsa-driver snapshot?

Takashi

#59 lore raw

At Mon, 18 Jul 2011 09:35:33 +0200,

Quoted 38 lines · Takashi Iwai

At Sun, 17 Jul 2011 14:17:22 +0200,

Quoted 35 lines · Julian Sikorski

W dniu 17.07.2011 13:55, Julian Sikorski pisze:

Quoted 33 lines

W dniu 05.07.2011 03:31, Raymond Yau pisze:

Quoted 15 lines

2011/7/5 Julian Sikorski<[email protected]>:

Quoted 4 lines

From what I was able to decipher, 0x1e is a jack, external rear, with spdif out default output and optical connection. It is black. The same physical socket is used for the last 2 surround channels. Could you please clarify? Thanks in advance.

Take a look at Block Diagram of alc892 datasheet

http://www.realtek.com/products/productsView.aspx?Langid=1&PNid=24&PFid=28&Level=5&Conn=4&ProdID=284

if you can confirmed the internal mic, mic jack ,line in , line out and internal speaker work as expected

Quoted 8 lines

the only pin complex which can be connected to rear [Audio Output] 0x0d is 0x15

seem that the pin complex for 4 jack 8-ch notebook are different from desktop with 6 jacks at rear panel

a 10 channel codec is able to provide volume control for internal speaker and 4 jacks

Thanks to Raymond's advice I was finally able to make the sound come out of the copper part of the spdif/side surround jack. I am pasting the diff created with hda-analyzer, please let me know if this gives you enough information to add proper 7.1 sound support for this laptop. Here is the alsa-info.sh with all jacks playing sound:
http://www.alsa-project.org/db/?f=8f23e499727ec612ed925b81d3f38928e8f6aebb
Of course, there is still no specific volume control for the side channel.

Quoted 8 lines
Quoted 6 lines
Quoted 2 lines

Julian

Upon further investigation I discovered that with the volume on the 0x17 can be controlled with center/lfe in alsamixer. I don't think it is the intended behaviour.

Is it with the very latest alsa-driver snapshot?

And I can't reproduce your problem with the alsa-info.sh output above. Give more exact information what you did and what is the problem.

thanks,

Takashi

#60 lore raw

W dniu 18.07.2011 10:52, Takashi Iwai pisze:

Quoted 7 lines

And I can't reproduce your problem with the alsa-info.sh output above. Give more exact information what you did and what is the problem.

thanks,

Takashi

I'm sorry for the confusion - let me sum up the current situation. With the fixes you pushed to sound-2.6/master I was able to get 5.1 sound out of my laptop. The only missing bit was the 7.1 sound. And the last channel goes via a jack/optical spdif hybrid. The problem is that the BIOS does not announce that and as such alsa is unaware of the side surround channel. Using Raymond's advice, I was able to make the sound come out of the last jack, by changing some values for pin 0x17 (described as sidesurr in the datasheet), diff is attached. I basically checked what was the difference in alsa-info.sh output when I was changing number of channels with alsamixer, and then did the same for pin 0x17. Since, from what I understood, you wanted me to figure out which pin is connected to the last jack [1], I thought this information would be useful to fix BIOS shortcomings.
Other problem is that the volume on that jack is controlled by center and lfe sliders (in alsamixer), which is probably caused by the fact that alsa is unaware of the 7.1 sound.
If more information is needed, please let me know what do you need in addition to alsa-info.sh output.

Regards,
Julian

[1] http://article.gmane.org/gmane.linux.alsa.devel/86749

Diff for codec 0/0 (0x10ec0892):

(quoted diff) +2 -2
@@ -223,23 +223,23 @@
     Misc = NO_PRESENCE
   Pin-ctls: 0x20: IN
   Unsolicited: tag=0x00, enabled=0
   Power: setting=D0, actual=D0
   Connection: 1
      0x0e
 Node 0x17 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
   Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
-  Amp-Out vals: [0x00 0x00]
+  Amp-Out vals: [0x80 0x80]
   Pincap 0x00000036: IN OUT Detect Trigger
   Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
     Conn = 1/8, Color = Black
     DefAssociation = 0xf, Sequence = 0x0
     Misc = NO_PRESENCE
-  Pin-ctls: 0x40: OUT
+  Pin-ctls: 0x20: IN
   Unsolicited: tag=0x00, enabled=0
   Power: setting=D0, actual=D0
   Connection: 1
      0x0f
 Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
   Control: name="Center Playback Switch", index=0, device=0
     ControlAmp: chs=1, dir=1, idx=0, ofs=0
   Control: name="LFE Playback Switch", index=0, device=0
#61 lore raw

W dniu 18.07.2011 13:15, Julian Sikorski pisze:

Quoted 28 lines

W dniu 18.07.2011 10:52, Takashi Iwai pisze:

Quoted 7 lines

And I can't reproduce your problem with the alsa-info.sh output above. Give more exact information what you did and what is the problem.

thanks,

Takashi

I'm sorry for the confusion - let me sum up the current situation. With the fixes you pushed to sound-2.6/master I was able to get 5.1 sound out of my laptop. The only missing bit was the 7.1 sound. And the last channel goes via a jack/optical spdif hybrid. The problem is that the BIOS does not announce that and as such alsa is unaware of the side surround channel.
Using Raymond's advice, I was able to make the sound come out of the last jack, by changing some values for pin 0x17 (described as sidesurr in the datasheet), diff is attached. I basically checked what was the difference in alsa-info.sh output when I was changing number of channels with alsamixer, and then did the same for pin 0x17.
Since, from what I understood, you wanted me to figure out which pin is connected to the last jack [1], I thought this information would be useful to fix BIOS shortcomings.
Other problem is that the volume on that jack is controlled by center and lfe sliders (in alsamixer), which is probably caused by the fact that alsa is unaware of the 7.1 sound.
If more information is needed, please let me know what do you need in addition to alsa-info.sh output.

Quoted 4 lines

Regards,
Julian

[1] http://article.gmane.org/gmane.linux.alsa.devel/86749

The diff is reverted for some reason - setting pin-ctls to 0x40: OUT and Amp-Out vals to [0x00 0x00] is what makes the sound appear. Sorry for the confusion.

Julian

#62 lore raw
In reply to Julian Sikorski

At Mon, 18 Jul 2011 13:15:14 +0200,

Quoted 9 lines · Julian Sikorski

W dniu 18.07.2011 10:52, Takashi Iwai pisze:

Quoted 7 lines

And I can't reproduce your problem with the alsa-info.sh output above. Give more exact information what you did and what is the problem.

thanks,

Takashi

Quoted 14 lines

I'm sorry for the confusion - let me sum up the current situation. With the fixes you pushed to sound-2.6/master I was able to get 5.1 sound out of my laptop. The only missing bit was the 7.1 sound. And the last channel goes via a jack/optical spdif hybrid. The problem is that the BIOS does not announce that and as such alsa is unaware of the side surround channel.
Using Raymond's advice, I was able to make the sound come out of the last jack, by changing some values for pin 0x17 (described as sidesurr in the datasheet), diff is attached. I basically checked what was the difference in alsa-info.sh output when I was changing number of channels with alsamixer, and then did the same for pin 0x17.
Since, from what I understood, you wanted me to figure out which pin is connected to the last jack [1], I thought this information would be useful to fix BIOS shortcomings.

Yes, and note that you can set up the initial pin configurations dynamically via sysfs, too.

Quoted 3 lines

Other problem is that the volume on that jack is controlled by center and lfe sliders (in alsamixer), which is probably caused by the fact that alsa is unaware of the 7.1 sound.

And this is not what I can't reproduce.

Quoted 2 lines

If more information is needed, please let me know what do you need in addition to alsa-info.sh output.

First off, double-check whether the CLFE mixer really changes the pin amp. At best, take alsa-info.sh output snapshot before and after changing the mixer state, and compare the files (better give both files in the mail).

Takashi

#63 lore raw

W dniu 18.07.2011 13:19, Takashi Iwai pisze:

Quoted 26 lines

At Mon, 18 Jul 2011 13:15:14 +0200,

Quoted 9 lines · Julian Sikorski

W dniu 18.07.2011 10:52, Takashi Iwai pisze:

Quoted 7 lines

And I can't reproduce your problem with the alsa-info.sh output above. Give more exact information what you did and what is the problem.

thanks,

Takashi

Quoted 14 lines

I'm sorry for the confusion - let me sum up the current situation. With the fixes you pushed to sound-2.6/master I was able to get 5.1 sound out of my laptop. The only missing bit was the 7.1 sound. And the last channel goes via a jack/optical spdif hybrid. The problem is that the BIOS does not announce that and as such alsa is unaware of the side surround channel.
Using Raymond's advice, I was able to make the sound come out of the last jack, by changing some values for pin 0x17 (described as sidesurr in the datasheet), diff is attached. I basically checked what was the difference in alsa-info.sh output when I was changing number of channels with alsamixer, and then did the same for pin 0x17.
Since, from what I understood, you wanted me to figure out which pin is connected to the last jack [1], I thought this information would be useful to fix BIOS shortcomings.

Quoted 2 lines

Yes, and note that you can set up the initial pin configurations dynamically via sysfs, too.

I tried, but without much success [2] - I came up with 0x01111xxx, but I do not have enough understanding on what to put as the last 3 numbers. Moreover, I keep getting this upon trying to apply the new pin configuration:

# echo 0x17 0x011111f0 > user_pin_configs
# LANG=C pasuspender echo 1 > reconfig
echo: write error: Device or resource busy
Quoted 6 lines
Quoted 3 lines

Other problem is that the volume on that jack is controlled by center and lfe sliders (in alsamixer), which is probably caused by the fact that alsa is unaware of the 7.1 sound.

And this is not what I can't reproduce.

Quoted 7 lines
Quoted 2 lines

If more information is needed, please let me know what do you need in addition to alsa-info.sh output.

First off, double-check whether the CLFE mixer really changes the pin amp. At best, take alsa-info.sh output snapshot before and after changing the mixer state, and compare the files (better give both files in the mail).

Here you go. playing.txt is the state when sound comes out of the spdif/side pin, and the center-lfe-half-volume.txt is when the volume is reduced to 50 % afterwards. Please keep in mind that if you enable 6-channel sound with alsamixer, the volume on center/lfe-mic jack will be reduced too (8-channel-half-volume.txt)

Quoted 2 lines

Takashi

Julian

[2] http://article.gmane.org/gmane.linux.alsa.devel/86878

upload=true&script=true&cardinfo=
!!################################
!!ALSA Information Script v 0.4.60
!!################################

!!Script ran on: Mon Jul 18 11:22:55 UTC 2011

!!Linux Distribution
!!------------------

Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock)

!!DMI Information
!!---------------

Manufacturer:      CLEVO                            
Product Name:      P150HMx
Product Version:   Not Applicable                    

!!Kernel Information
!!------------------

Kernel release:    3.0-0.rc7.git3.1.belegdol.fc15.x86_64
Operating System:  GNU/Linux
Architecture:      x86_64
Processor:         x86_64
SMP Enabled:       Yes

!!ALSA Version
!!------------

Driver version:     1.0.24
Library version:    1.0.24
Utilities version:  1.0.24.1

!!Loaded ALSA modules
!!-------------------

snd_hda_intel
snd_hda_intel

!!Sound Servers on this system
!!----------------------------

Pulseaudio:
Installed - Yes (/usr/bin/pulseaudio)
Running - Yes

Jack:
Installed - Yes (/usr/bin/jackd)
Running - No

!!Soundcards recognised by ALSA
!!-----------------------------

0 [PCH ]: HDA-Intel - HDA Intel PCH

                      HDA Intel PCH at 0xf6500000 irq 52
 1 [NVidia         ]: HDA-Intel - HDA NVidia
                      HDA NVidia at 0xf6080000 irq 17

!!PCI Soundcards installed in the system
!!--------------------------------------

00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 01:00.1 Audio device: nVidia Corporation Device 0beb (rev a1)

!!Advanced information - PCI Vendor/Device/Subsystem ID's !!--------------------------------------------------------

00:1b.0 0403: 8086:1c20 (rev 05)

	Subsystem: 1558:5102
--
01:00.1 0403: 10de:0beb (rev a1)
	Subsystem: 1558:5102

!!Loaded sound module options
!!--------------------------

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!HDA-Intel Codec information
!!---------------------------
--startcollapse--

Codec: Realtek ALC892
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0892
Subsystem Id: 0x15585102
Revision Id: 0x100302
No Modem Function Group found
Default PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Speaker Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Device: name="ALC892 Analog", type="Audio", device=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Surround Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x05 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Center Playback Volume", index=0, device=0

    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Volume", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Control: name="IEC958 Default PCM Playback Switch", index=0, device=0
Device: name="ALC892 Digital", type="SPDIF", device=1
Converter: stream=5, channel=0
Digital: Enabled
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=0, device=0
Control: name="Capture Volume", index=0, device=0
Device: name="ALC892 Analog", type="Audio", device=0 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x1b 0x1b]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x23

Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=1, device=0
Control: name="Capture Volume", index=1, device=0
Device: name="ALC892 Analog", type="Audio", device=2 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x80 0x80]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x22

Node 0x0a [Audio Input] wcaps 0x100711: Stereo Digital
Converter: stream=0, channel=0
SDI-Select: 0
Digital:
Digital category: 0x0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x1f
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Internal Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Internal Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Line Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Control: name="Line Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
  Amp-In vals:  [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
  Connection: 10
     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17

Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00]
Connection: 2

     0x02 0x0b

Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00]
Connection: 2

     0x03 0x0b

Node 0x0e [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x04 0x0b

Node 0x0f [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x05 0x0b

Node 0x10 [Audio Output] wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x11 [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x10

Node 0x12 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x0001003e: IN OUT HP EAPD Detect Trigger
  EAPD 0x2: EAPD
  Pin Default 0x99130110: [Fixed] Speaker at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x0c

Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0d

Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0e

Node 0x17 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0f
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Center Playback Switch", index=0, device=0
    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Switch", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Control: name="Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x01a11c30: [Jack] Mic at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0x0
  Pin-ctls: 0x21: IN VREF_50
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x19 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Internal Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x0000373e: IN OUT HP Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x99a30931: [Fixed] Mic at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x3, Sequence = 0x1
    Misc = NO_PRESENCE
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1a [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Surround Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x0181143f: [Jack] Line In at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0xf
  Pin-ctls: 0x20: IN VREF_HIZ
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Headphone Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x0001373e: IN OUT HP EAPD Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  EAPD 0x2: EAPD
  Pin Default 0x0121101f: [Jack] HP Out at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x1, Sequence = 0xf
  Pin-ctls: 0xc0: OUT HP VREF_HIZ
  Unsolicited: tag=04, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c 0x0d* 0x0e 0x0f 0x26

Node 0x1c [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x00000024: IN Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1d [Pin Complex] wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x598301f0: [N/A] Line In at Int ATAPI
Conn = ATAPI, Color = Unknown DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x01451120: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = Black DefAssociation = 0x2, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x06

Node 0x1f [Pin Complex] wcaps 0x400681: Stereo Digital
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=24
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=1, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 12

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b 0x12

Node 0x23 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=0, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 11

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b

Node 0x24 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x25 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0 Amp-Out vals: [0x40 0x40]
Converter: stream=0, channel=0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x26 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x25 0x0b

Codec: Nvidia GPU 12 HDMI/DP
Address: 0
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital: Enabled GenLevel
Digital category: 0x2
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 1
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=2, device=0
Control: name="IEC958 Playback Pro Mask", index=2, device=0
Control: name="IEC958 Playback Default", index=2, device=0
Control: name="IEC958 Playback Switch", index=2, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 3
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=3, device=0
Control: name="IEC958 Playback Pro Mask", index=3, device=0
Control: name="IEC958 Playback Default", index=3, device=0
Control: name="IEC958 Playback Switch", index=3, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

--endcollapse--

!!ALSA Device nodes
!!-----------------

crw-rw----+ 1 root audio 116, 7 Jul 17 21:29 /dev/snd/controlC0 crw-rw----+ 1 root audio 116, 16 Jul 17 21:29 /dev/snd/controlC1 crw-rw----+ 1 root audio 116, 6 Jul 17 21:29 /dev/snd/hwC0D0 crw-rw----+ 1 root audio 116, 15 Jul 17 21:29 /dev/snd/hwC1D0 crw-rw----+ 1 root audio 116, 14 Jul 17 21:29 /dev/snd/hwC1D1 crw-rw----+ 1 root audio 116, 13 Jul 17 21:29 /dev/snd/hwC1D2 crw-rw----+ 1 root audio 116, 12 Jul 17 21:29 /dev/snd/hwC1D3

crw-rw----+ 1 root audio 116,  5 Jul 17 21:56 /dev/snd/pcmC0D0c
crw-rw----+ 1 root audio 116,  4 Jul 18 13:16 /dev/snd/pcmC0D0p
crw-rw----+ 1 root audio 116,  3 Jul 17 21:31 /dev/snd/pcmC0D1p
crw-rw----+ 1 root audio 116,  2 Jul 17 21:29 /dev/snd/pcmC0D2c
crw-rw----+ 1 root audio 116, 11 Jul 17 21:56 /dev/snd/pcmC1D3p
crw-rw----+ 1 root audio 116, 10 Jul 17 21:29 /dev/snd/pcmC1D7p
crw-rw----+ 1 root audio 116,  9 Jul 17 21:29 /dev/snd/pcmC1D8p
crw-rw----+ 1 root audio 116,  8 Jul 17 21:29 /dev/snd/pcmC1D9p
crw-rw----+ 1 root audio 116,  1 Jul 17 21:29 /dev/snd/seq

crw-rw----+ 1 root audio 116, 33 Jul 17 21:29 /dev/snd/timer

/dev/snd/by-path:
total 0
drwxr-xr-x. 2 root root 80 Jul 17 21:29 .
drwxr-xr-x. 3 root root 400 Jul 17 21:29 ..
lrwxrwxrwx. 1 root root 12 Jul 17 21:29 pci-0000:00:1b.0 -> ../controlC0 lrwxrwxrwx. 1 root root 12 Jul 17 21:29 pci-0000:01:00.1 -> ../controlC1

!!ALSA configuration files
!!------------------------

!!System wide config file (/etc/asound.conf)

#
# Place your global alsa-lib configuration here... #

@hooks [

	{
		func load
		files [
			"/etc/alsa/pulse-default.conf"
		]
		errors false
	}

]

!!Aplay/Arecord output
!!------------

APLAY

**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0

ARECORD

**** List of CAPTURE Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 2: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0

!!Amixer output
!!-------------

!!-------Mixer controls for card 0 [PCH]

Card hw:0 'PCH'/'HDA Intel PCH at 0xf6500000 irq 52'
Mixer name : 'Realtek ALC892'
Components : 'HDA:10ec0892,15585102,00100302'
Controls : 34
Simple ctrls : 20
Simple mixer control 'Master',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 55 [86%] [-9.00dB] [on]
Simple mixer control 'Headphone',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Speaker',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'PCM',0
Capabilities: pvolume penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 254 [100%] [0.20dB]
Front Right: Playback 254 [100%] [0.20dB]
Simple mixer control 'Surround',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Center',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'LFE',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Line',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958 Default PCM',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 27 [59%] [11.00dB] [on]
Front Right: Capture 27 [59%] [11.00dB] [on]
Simple mixer control 'Capture',1
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 0 [0%] [-16.00dB] [off]
Front Right: Capture 0 [0%] [-16.00dB] [off]
Simple mixer control 'Auto-Mute Mode',0
Capabilities: enum
Items: 'Disabled' 'Enabled'
Item0: 'Enabled'
Simple mixer control 'Channel Mode',0
Capabilities: enum
Items: '2ch' '4ch' '6ch'
Item0: '2ch'
Simple mixer control 'Input Source',0
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Mic'
Simple mixer control 'Input Source',1
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Mic'
Simple mixer control 'Internal Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Internal Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]

!!-------Mixer controls for card 1 [NVidia]

Card hw:1 'NVidia'/'HDA NVidia at 0xf6080000 irq 17'
Mixer name : 'Nvidia GPU 12 HDMI/DP'
Components : 'HDA:10de0012,10de0101,00100100'
Controls : 16
Simple ctrls : 4
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958',1
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',2
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',3
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]

!!Alsactl output
!!-------------

--startcollapse--

state.PCH {
	control.1 {
		iface MIXER
		name 'Channel Mode'
		value '2ch'
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 '2ch'
			item.1 '4ch'
			item.2 '6ch'
		}
	}
	control.2 {
		iface MIXER
		name 'Headphone Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.3 {
		iface MIXER
		name 'Headphone Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.4 {
		iface MIXER
		name 'Surround Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.5 {
		iface MIXER
		name 'Surround Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.6 {
		iface MIXER
		name 'Center Playback Volume'
		value 64
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
		}
	}
	control.7 {
		iface MIXER
		name 'LFE Playback Volume'
		value 64
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
		}
	}
	control.8 {
		iface MIXER
		name 'Center Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'LFE Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'Speaker Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.11 {
		iface MIXER
		name 'Speaker Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.12 {
		iface MIXER
		name 'Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.13 {
		iface MIXER
		name 'Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.14 {
		iface MIXER
		name 'Internal Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.15 {
		iface MIXER
		name 'Internal Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.16 {
		iface MIXER
		name 'Line Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.17 {
		iface MIXER
		name 'Line Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.18 {
		iface MIXER
		name 'Auto-Mute Mode'
		value Enabled
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Disabled
			item.1 Enabled
		}
	}
	control.19 {
		iface MIXER
		name 'Mic Boost Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.20 {
		iface MIXER
		name 'Internal Mic Boost Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.21 {
		iface MIXER
		name 'Capture Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.22 {
		iface MIXER
		name 'Capture Switch'
		index 1
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.23 {
		iface MIXER
		name 'Capture Volume'
		value.0 27
		value.1 27
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 1100
			dbvalue.1 1100
		}
	}
	control.24 {
		iface MIXER
		name 'Capture Volume'
		index 1
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 -1600
			dbvalue.1 -1600
		}
	}
	control.25 {
		iface MIXER
		name 'Input Source'
		value Mic
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.26 {
		iface MIXER
		name 'Input Source'
		index 1
		value Mic
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.27 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.28 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.29 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.30 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.31 {
		iface MIXER
		name 'IEC958 Default PCM Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.32 {
		iface MIXER
		name 'Master Playback Volume'
		value 55
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 -900
		}
	}
	control.33 {
		iface MIXER
		name 'Master Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.34 {
		iface MIXER
		name 'PCM Playback Volume'
		value.0 254
		value.1 254
		comment {
			access 'read write user'
			type INTEGER
			count 2
			range '0 - 255'
			tlv '0000000100000008ffffec1400000014'
			dbmin -5100
			dbmax 0
			dbvalue.0 -20
			dbvalue.1 -20
		}
	}
}
state.NVidia {
	control.1 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.2 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.3 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.4 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.5 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 1
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.6 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 1
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.7 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 1
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.8 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 1
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 2
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 2
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.11 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 2
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.12 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 2
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.13 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 3
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.14 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 3
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.15 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 3
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.16 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 3
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
}

--endcollapse--

!!All Loaded Modules
!!------------------

Module
tcp_lp
ebtable_nat
ebtables
ipt_MASQUERADE
iptable_nat
nf_nat
xt_CHECKSUM
iptable_mangle
bridge
stp
llc
ppdev
parport_pc
lp
parport
sunrpc
bnep
bluetooth
nf_conntrack_ipv4
nf_defrag_ipv4
ip6t_REJECT
nf_conntrack_ipv6
nf_defrag_ipv6
xt_state
nf_conntrack
ip6table_filter
ip6_tables
nvidia
snd_hda_codec_hdmi
snd_hda_codec_realtek
fuse
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_seq
snd_seq_device
snd_pcm
snd_timer
snd
arc4
iwlagn
mac80211
uvcvideo
videodev
i2c_i801
soundcore
cfg80211
microcode
jmb38x_ms
xhci_hcd
joydev
media
v4l2_compat_ioctl32
snd_page_alloc
rfkill
jme
serio_raw
memstick
i2c_core
mii
iTCO_wdt
iTCO_vendor_support
binfmt_misc
virtio_net
kvm_intel
kvm
firewire_ohci
firewire_core
crc_itu_t
sdhci_pci
sdhci
mmc_core
wmi
video

!!Sysfs Files
!!-----------

/sys/class/sound/hwC0D0/init_pin_configs:
0x11 0x411111f0
0x12 0x411111f0
0x14 0x99130110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x411111f0
0x18 0x01a11c30
0x19 0x99a30931
0x1a 0x0181143f
0x1b 0x0121101f
0x1c 0x411111f0
0x1d 0x598301f0
0x1e 0x01451120
0x1f 0x411111f0

/sys/class/sound/hwC0D0/driver_pin_configs:

/sys/class/sound/hwC0D0/user_pin_configs:

/sys/class/sound/hwC0D0/init_verbs:

/sys/class/sound/hwC1D0/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D0/driver_pin_configs:

/sys/class/sound/hwC1D0/user_pin_configs:

/sys/class/sound/hwC1D0/init_verbs:

/sys/class/sound/hwC1D1/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D1/driver_pin_configs:

/sys/class/sound/hwC1D1/user_pin_configs:

/sys/class/sound/hwC1D1/init_verbs:

/sys/class/sound/hwC1D2/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D2/driver_pin_configs:

/sys/class/sound/hwC1D2/user_pin_configs:

/sys/class/sound/hwC1D2/init_verbs:

/sys/class/sound/hwC1D3/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D3/driver_pin_configs:

/sys/class/sound/hwC1D3/user_pin_configs:

/sys/class/sound/hwC1D3/init_verbs:

!!ALSA/HDA dmesg
!!------------------

[   11.619432] Disabling lock debugging due to kernel taint
[   11.631239] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   11.631334] snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
[   11.631356] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[   11.635107] fuse init (API version 7.16)
[   11.641039] SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
[   11.691510] hda_codec: ALC892: SKU not ready 0x598301f0
[   11.691680] hda_codec: ALC892: BIOS auto-probing.
[   11.691690] ALSA sound/pci/hda/hda_codec.c:4878 autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   11.691695] ALSA sound/pci/hda/hda_codec.c:4882    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   11.691699] ALSA sound/pci/hda/hda_codec.c:4886    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   11.691703] ALSA sound/pci/hda/hda_codec.c:4887    mono: mono_out=0x0
[   11.691706] ALSA sound/pci/hda/hda_codec.c:4890    dig-out=0x1e/0x0
[   11.691709] ALSA sound/pci/hda/hda_codec.c:4891    inputs:
[   11.691714] ALSA sound/pci/hda/hda_codec.c:4895  Mic=0x18
[   11.691718] ALSA sound/pci/hda/hda_codec.c:4895  Internal Mic=0x19
[   11.691721] ALSA sound/pci/hda/hda_codec.c:4895  Line=0x1a
[   11.691724] ALSA sound/pci/hda/hda_codec.c:4897 
[   11.693727] ALSA sound/pci/hda/patch_realtek.c:1267 realtek: No valid SSID, checking pincfg 0x598301f0 for NID 0x1d
[   11.693732] ALSA sound/pci/hda/patch_realtek.c:1348 realtek: Enable default setup for auto mode as fallback
[   11.698816] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   11.699014] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   11.699018] hda_intel: Disabling MSI
[   11.699119] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[   11.705661] ALSA sound/pci/hda/hda_intel.c:1454 Enable delay in RIRB handling
[   11.848573] SELinux: initialized (dev sda2, type fuseblk), uses genfs_contexts
--
[   11.850026] ntfs-3g[887]: Ownership and permissions disabled, configuration type 1
[   11.924388] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.963381] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0
[   12.002301] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0
[   12.041251] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[   12.064072] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13
[   12.064355] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[   12.064601] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[   12.064848] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[   12.158375] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
--
[   26.077130] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[   31.161238] hda-intel: Invalid position buffer, using LPIB read method instead.
[   31.269629] hda-intel: Invalid position buffer, using LPIB read method instead.
[   31.296939] hda-intel: Invalid position buffer, using LPIB read method instead.
[   32.159940] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
[   32.267858] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[   34.734137] wlan0: no IPv6 routers present
--
[17414.913286] ehci_hcd 0000:00:1d.0: PCI INT A disabled
[17415.204932] snd_hda_intel 0000:00:1b.0: PCI INT A disabled
[17415.317829] snd_hda_intel 0000:01:00.1: PCI INT B disabled
[17415.317883] ACPI handle has no context!
--
[17416.126533] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
[17416.126557] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x103)
[17416.126569] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[17416.126573] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
[17416.126597] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x10010b)
--
[17416.126927] nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x800010, writing 0x800000)
[17416.126962] snd_hda_intel 0000:01:00.1: restoring config space at offset 0x1 (was 0x100006, writing 0x100002)
[17416.127008] xhci_hcd 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
--
[17416.127905] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[17416.127949] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[17416.127955] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[17416.127988] snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
[17416.128020] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
--
[17416.128056] ahci 0000:00:1f.2: setting latency timer to 64
[17416.128072] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[17416.128079] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[17416.128124] xhci_hcd 0000:02:00.0: setting latency timer to 64
--
[22590.768834] jmb38x_ms 0000:03:00.3: PCI INT B disabled
[22590.768930] snd_hda_intel 0000:01:00.1: PCI INT B disabled
[22590.768941] sdhci-pci 0000:03:00.1: PCI INT B disabled
--
[22590.779515] ehci_hcd 0000:00:1a.0: PCI INT A disabled
[22591.070773] snd_hda_intel 0000:00:1b.0: PCI INT A disabled
[22591.409020] PM: suspend of devices complete after 1206.070 msecs
--
[22592.164726] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
[22592.164749] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x103)
[22592.164762] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[22592.164766] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
[22592.164790] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x10010b)
--
[22592.165121] nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x800010, writing 0x800000)
[22592.165157] snd_hda_intel 0000:01:00.1: restoring config space at offset 0x1 (was 0x100006, writing 0x100002)
[22592.165202] xhci_hcd 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
--
[22592.166108] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[22592.166113] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[22592.166116] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[22592.166121] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[22592.166132] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[22592.166143] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[22592.166170] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[22592.166182] snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
[22592.166185] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[22592.166272] xhci_hcd 0000:02:00.0: setting latency timer to 64

upload=true&script=true&cardinfo=
!!################################
!!ALSA Information Script v 0.4.60
!!################################

!!Script ran on: Mon Jul 18 11:23:47 UTC 2011

!!Linux Distribution
!!------------------

Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock)

!!DMI Information
!!---------------

Manufacturer:      CLEVO                            
Product Name:      P150HMx
Product Version:   Not Applicable                    

!!Kernel Information
!!------------------

Kernel release:    3.0-0.rc7.git3.1.belegdol.fc15.x86_64
Operating System:  GNU/Linux
Architecture:      x86_64
Processor:         x86_64
SMP Enabled:       Yes

!!ALSA Version
!!------------

Driver version:     1.0.24
Library version:    1.0.24
Utilities version:  1.0.24.1

!!Loaded ALSA modules
!!-------------------

snd_hda_intel
snd_hda_intel

!!Sound Servers on this system
!!----------------------------

Pulseaudio:
Installed - Yes (/usr/bin/pulseaudio)
Running - Yes

Jack:
Installed - Yes (/usr/bin/jackd)
Running - No

!!Soundcards recognised by ALSA
!!-----------------------------

0 [PCH ]: HDA-Intel - HDA Intel PCH

                      HDA Intel PCH at 0xf6500000 irq 52
 1 [NVidia         ]: HDA-Intel - HDA NVidia
                      HDA NVidia at 0xf6080000 irq 17

!!PCI Soundcards installed in the system
!!--------------------------------------

00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 01:00.1 Audio device: nVidia Corporation Device 0beb (rev a1)

!!Advanced information - PCI Vendor/Device/Subsystem ID's !!--------------------------------------------------------

00:1b.0 0403: 8086:1c20 (rev 05)

	Subsystem: 1558:5102
--
01:00.1 0403: 10de:0beb (rev a1)
	Subsystem: 1558:5102

!!Loaded sound module options
!!--------------------------

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!HDA-Intel Codec information
!!---------------------------
--startcollapse--

Codec: Realtek ALC892
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0892
Subsystem Id: 0x15585102
Revision Id: 0x100302
No Modem Function Group found
Default PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Speaker Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Device: name="ALC892 Analog", type="Audio", device=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Surround Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x05 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Center Playback Volume", index=0, device=0

    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Volume", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x27 0x27]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Control: name="IEC958 Default PCM Playback Switch", index=0, device=0
Device: name="ALC892 Digital", type="SPDIF", device=1
Converter: stream=5, channel=0
Digital: Enabled
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=0, device=0
Control: name="Capture Volume", index=0, device=0
Device: name="ALC892 Analog", type="Audio", device=0 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x1b 0x1b]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x23

Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=1, device=0
Control: name="Capture Volume", index=1, device=0
Device: name="ALC892 Analog", type="Audio", device=2 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x80 0x80]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x22

Node 0x0a [Audio Input] wcaps 0x100711: Stereo Digital
Converter: stream=0, channel=0
SDI-Select: 0
Digital:
Digital category: 0x0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x1f
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Internal Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Internal Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Line Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Control: name="Line Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
  Amp-In vals:  [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
  Connection: 10
     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17

Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00]
Connection: 2

     0x02 0x0b

Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00]
Connection: 2

     0x03 0x0b

Node 0x0e [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x04 0x0b

Node 0x0f [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x05 0x0b

Node 0x10 [Audio Output] wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x11 [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x10

Node 0x12 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x0001003e: IN OUT HP EAPD Detect Trigger
  EAPD 0x2: EAPD
  Pin Default 0x99130110: [Fixed] Speaker at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x0c

Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0d

Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0e

Node 0x17 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0f
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Center Playback Switch", index=0, device=0
    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Switch", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Control: name="Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x01a11c30: [Jack] Mic at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0x0
  Pin-ctls: 0x21: IN VREF_50
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x19 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Internal Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x0000373e: IN OUT HP Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x99a30931: [Fixed] Mic at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x3, Sequence = 0x1
    Misc = NO_PRESENCE
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1a [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Surround Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x0181143f: [Jack] Line In at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0xf
  Pin-ctls: 0x20: IN VREF_HIZ
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Headphone Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x0001373e: IN OUT HP EAPD Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  EAPD 0x2: EAPD
  Pin Default 0x0121101f: [Jack] HP Out at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x1, Sequence = 0xf
  Pin-ctls: 0xc0: OUT HP VREF_HIZ
  Unsolicited: tag=04, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c 0x0d* 0x0e 0x0f 0x26

Node 0x1c [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x00000024: IN Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1d [Pin Complex] wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x598301f0: [N/A] Line In at Int ATAPI
Conn = ATAPI, Color = Unknown DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x01451120: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = Black DefAssociation = 0x2, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x06

Node 0x1f [Pin Complex] wcaps 0x400681: Stereo Digital
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=24
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=1, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 12

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b 0x12

Node 0x23 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=0, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 11

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b

Node 0x24 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x25 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0 Amp-Out vals: [0x40 0x40]
Converter: stream=0, channel=0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x26 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x25 0x0b

Codec: Nvidia GPU 12 HDMI/DP
Address: 0
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital: Enabled GenLevel
Digital category: 0x2
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 1
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=2, device=0
Control: name="IEC958 Playback Pro Mask", index=2, device=0
Control: name="IEC958 Playback Default", index=2, device=0
Control: name="IEC958 Playback Switch", index=2, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 3
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=3, device=0
Control: name="IEC958 Playback Pro Mask", index=3, device=0
Control: name="IEC958 Playback Default", index=3, device=0
Control: name="IEC958 Playback Switch", index=3, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

--endcollapse--

!!ALSA Device nodes
!!-----------------

crw-rw----+ 1 root audio 116, 7 Jul 17 21:29 /dev/snd/controlC0 crw-rw----+ 1 root audio 116, 16 Jul 17 21:29 /dev/snd/controlC1 crw-rw----+ 1 root audio 116, 6 Jul 17 21:29 /dev/snd/hwC0D0 crw-rw----+ 1 root audio 116, 15 Jul 17 21:29 /dev/snd/hwC1D0 crw-rw----+ 1 root audio 116, 14 Jul 17 21:29 /dev/snd/hwC1D1 crw-rw----+ 1 root audio 116, 13 Jul 17 21:29 /dev/snd/hwC1D2 crw-rw----+ 1 root audio 116, 12 Jul 17 21:29 /dev/snd/hwC1D3

crw-rw----+ 1 root audio 116,  5 Jul 17 21:56 /dev/snd/pcmC0D0c
crw-rw----+ 1 root audio 116,  4 Jul 18 13:16 /dev/snd/pcmC0D0p
crw-rw----+ 1 root audio 116,  3 Jul 17 21:31 /dev/snd/pcmC0D1p
crw-rw----+ 1 root audio 116,  2 Jul 17 21:29 /dev/snd/pcmC0D2c
crw-rw----+ 1 root audio 116, 11 Jul 17 21:56 /dev/snd/pcmC1D3p
crw-rw----+ 1 root audio 116, 10 Jul 17 21:29 /dev/snd/pcmC1D7p
crw-rw----+ 1 root audio 116,  9 Jul 17 21:29 /dev/snd/pcmC1D8p
crw-rw----+ 1 root audio 116,  8 Jul 17 21:29 /dev/snd/pcmC1D9p
crw-rw----+ 1 root audio 116,  1 Jul 17 21:29 /dev/snd/seq

crw-rw----+ 1 root audio 116, 33 Jul 17 21:29 /dev/snd/timer

/dev/snd/by-path:
total 0
drwxr-xr-x. 2 root root 80 Jul 17 21:29 .
drwxr-xr-x. 3 root root 400 Jul 17 21:29 ..
lrwxrwxrwx. 1 root root 12 Jul 17 21:29 pci-0000:00:1b.0 -> ../controlC0 lrwxrwxrwx. 1 root root 12 Jul 17 21:29 pci-0000:01:00.1 -> ../controlC1

!!ALSA configuration files
!!------------------------

!!System wide config file (/etc/asound.conf)

#
# Place your global alsa-lib configuration here... #

@hooks [

	{
		func load
		files [
			"/etc/alsa/pulse-default.conf"
		]
		errors false
	}

]

!!Aplay/Arecord output
!!------------

APLAY

**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0

ARECORD

**** List of CAPTURE Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 2: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0

!!Amixer output
!!-------------

!!-------Mixer controls for card 0 [PCH]

Card hw:0 'PCH'/'HDA Intel PCH at 0xf6500000 irq 52'
Mixer name : 'Realtek ALC892'
Components : 'HDA:10ec0892,15585102,00100302'
Controls : 34
Simple ctrls : 20
Simple mixer control 'Master',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 55 [86%] [-9.00dB] [on]
Simple mixer control 'Headphone',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Speaker',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'PCM',0
Capabilities: pvolume penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 254 [100%] [0.20dB]
Front Right: Playback 254 [100%] [0.20dB]
Simple mixer control 'Surround',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Center',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 48 [75%] [-16.00dB] [on]
Simple mixer control 'LFE',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 48 [75%] [-16.00dB] [on]
Simple mixer control 'Line',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958 Default PCM',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 27 [59%] [11.00dB] [on]
Front Right: Capture 27 [59%] [11.00dB] [on]
Simple mixer control 'Capture',1
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 0 [0%] [-16.00dB] [off]
Front Right: Capture 0 [0%] [-16.00dB] [off]
Simple mixer control 'Auto-Mute Mode',0
Capabilities: enum
Items: 'Disabled' 'Enabled'
Item0: 'Enabled'
Simple mixer control 'Channel Mode',0
Capabilities: enum
Items: '2ch' '4ch' '6ch'
Item0: '2ch'
Simple mixer control 'Input Source',0
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Mic'
Simple mixer control 'Input Source',1
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Mic'
Simple mixer control 'Internal Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Internal Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]

!!-------Mixer controls for card 1 [NVidia]

Card hw:1 'NVidia'/'HDA NVidia at 0xf6080000 irq 17'
Mixer name : 'Nvidia GPU 12 HDMI/DP'
Components : 'HDA:10de0012,10de0101,00100100'
Controls : 16
Simple ctrls : 4
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958',1
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',2
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',3
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]

!!Alsactl output
!!-------------

--startcollapse--

state.PCH {
	control.1 {
		iface MIXER
		name 'Channel Mode'
		value '2ch'
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 '2ch'
			item.1 '4ch'
			item.2 '6ch'
		}
	}
	control.2 {
		iface MIXER
		name 'Headphone Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.3 {
		iface MIXER
		name 'Headphone Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.4 {
		iface MIXER
		name 'Surround Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.5 {
		iface MIXER
		name 'Surround Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.6 {
		iface MIXER
		name 'Center Playback Volume'
		value 48
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 -1600
		}
	}
	control.7 {
		iface MIXER
		name 'LFE Playback Volume'
		value 48
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 -1600
		}
	}
	control.8 {
		iface MIXER
		name 'Center Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'LFE Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'Speaker Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.11 {
		iface MIXER
		name 'Speaker Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.12 {
		iface MIXER
		name 'Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.13 {
		iface MIXER
		name 'Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.14 {
		iface MIXER
		name 'Internal Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.15 {
		iface MIXER
		name 'Internal Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.16 {
		iface MIXER
		name 'Line Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.17 {
		iface MIXER
		name 'Line Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.18 {
		iface MIXER
		name 'Auto-Mute Mode'
		value Enabled
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Disabled
			item.1 Enabled
		}
	}
	control.19 {
		iface MIXER
		name 'Mic Boost Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.20 {
		iface MIXER
		name 'Internal Mic Boost Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.21 {
		iface MIXER
		name 'Capture Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.22 {
		iface MIXER
		name 'Capture Switch'
		index 1
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.23 {
		iface MIXER
		name 'Capture Volume'
		value.0 27
		value.1 27
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 1100
			dbvalue.1 1100
		}
	}
	control.24 {
		iface MIXER
		name 'Capture Volume'
		index 1
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 -1600
			dbvalue.1 -1600
		}
	}
	control.25 {
		iface MIXER
		name 'Input Source'
		value Mic
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.26 {
		iface MIXER
		name 'Input Source'
		index 1
		value Mic
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.27 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.28 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.29 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.30 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.31 {
		iface MIXER
		name 'IEC958 Default PCM Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.32 {
		iface MIXER
		name 'Master Playback Volume'
		value 55
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 -900
		}
	}
	control.33 {
		iface MIXER
		name 'Master Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.34 {
		iface MIXER
		name 'PCM Playback Volume'
		value.0 254
		value.1 254
		comment {
			access 'read write user'
			type INTEGER
			count 2
			range '0 - 255'
			tlv '0000000100000008ffffec1400000014'
			dbmin -5100
			dbmax 0
			dbvalue.0 -20
			dbvalue.1 -20
		}
	}
}
state.NVidia {
	control.1 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.2 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.3 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.4 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.5 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 1
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.6 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 1
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.7 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 1
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.8 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 1
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 2
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 2
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.11 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 2
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.12 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 2
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.13 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 3
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.14 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 3
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.15 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 3
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.16 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 3
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
}

--endcollapse--

!!All Loaded Modules
!!------------------

Module
tcp_lp
ebtable_nat
ebtables
ipt_MASQUERADE
iptable_nat
nf_nat
xt_CHECKSUM
iptable_mangle
bridge
stp
llc
ppdev
parport_pc
lp
parport
sunrpc
bnep
bluetooth
nf_conntrack_ipv4
nf_defrag_ipv4
ip6t_REJECT
nf_conntrack_ipv6
nf_defrag_ipv6
xt_state
nf_conntrack
ip6table_filter
ip6_tables
nvidia
snd_hda_codec_hdmi
snd_hda_codec_realtek
fuse
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_seq
snd_seq_device
snd_pcm
snd_timer
snd
arc4
iwlagn
mac80211
uvcvideo
videodev
i2c_i801
soundcore
cfg80211
microcode
jmb38x_ms
xhci_hcd
joydev
media
v4l2_compat_ioctl32
snd_page_alloc
rfkill
jme
serio_raw
memstick
i2c_core
mii
iTCO_wdt
iTCO_vendor_support
binfmt_misc
virtio_net
kvm_intel
kvm
firewire_ohci
firewire_core
crc_itu_t
sdhci_pci
sdhci
mmc_core
wmi
video

!!Sysfs Files
!!-----------

/sys/class/sound/hwC0D0/init_pin_configs:
0x11 0x411111f0
0x12 0x411111f0
0x14 0x99130110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x411111f0
0x18 0x01a11c30
0x19 0x99a30931
0x1a 0x0181143f
0x1b 0x0121101f
0x1c 0x411111f0
0x1d 0x598301f0
0x1e 0x01451120
0x1f 0x411111f0

/sys/class/sound/hwC0D0/driver_pin_configs:

/sys/class/sound/hwC0D0/user_pin_configs:

/sys/class/sound/hwC0D0/init_verbs:

/sys/class/sound/hwC1D0/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D0/driver_pin_configs:

/sys/class/sound/hwC1D0/user_pin_configs:

/sys/class/sound/hwC1D0/init_verbs:

/sys/class/sound/hwC1D1/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D1/driver_pin_configs:

/sys/class/sound/hwC1D1/user_pin_configs:

/sys/class/sound/hwC1D1/init_verbs:

/sys/class/sound/hwC1D2/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D2/driver_pin_configs:

/sys/class/sound/hwC1D2/user_pin_configs:

/sys/class/sound/hwC1D2/init_verbs:

/sys/class/sound/hwC1D3/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D3/driver_pin_configs:

/sys/class/sound/hwC1D3/user_pin_configs:

/sys/class/sound/hwC1D3/init_verbs:

!!ALSA/HDA dmesg
!!------------------

[   11.619432] Disabling lock debugging due to kernel taint
[   11.631239] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   11.631334] snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
[   11.631356] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[   11.635107] fuse init (API version 7.16)
[   11.641039] SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
[   11.691510] hda_codec: ALC892: SKU not ready 0x598301f0
[   11.691680] hda_codec: ALC892: BIOS auto-probing.
[   11.691690] ALSA sound/pci/hda/hda_codec.c:4878 autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   11.691695] ALSA sound/pci/hda/hda_codec.c:4882    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   11.691699] ALSA sound/pci/hda/hda_codec.c:4886    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   11.691703] ALSA sound/pci/hda/hda_codec.c:4887    mono: mono_out=0x0
[   11.691706] ALSA sound/pci/hda/hda_codec.c:4890    dig-out=0x1e/0x0
[   11.691709] ALSA sound/pci/hda/hda_codec.c:4891    inputs:
[   11.691714] ALSA sound/pci/hda/hda_codec.c:4895  Mic=0x18
[   11.691718] ALSA sound/pci/hda/hda_codec.c:4895  Internal Mic=0x19
[   11.691721] ALSA sound/pci/hda/hda_codec.c:4895  Line=0x1a
[   11.691724] ALSA sound/pci/hda/hda_codec.c:4897 
[   11.693727] ALSA sound/pci/hda/patch_realtek.c:1267 realtek: No valid SSID, checking pincfg 0x598301f0 for NID 0x1d
[   11.693732] ALSA sound/pci/hda/patch_realtek.c:1348 realtek: Enable default setup for auto mode as fallback
[   11.698816] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   11.699014] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   11.699018] hda_intel: Disabling MSI
[   11.699119] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[   11.705661] ALSA sound/pci/hda/hda_intel.c:1454 Enable delay in RIRB handling
[   11.848573] SELinux: initialized (dev sda2, type fuseblk), uses genfs_contexts
--
[   11.850026] ntfs-3g[887]: Ownership and permissions disabled, configuration type 1
[   11.924388] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.963381] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0
[   12.002301] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0
[   12.041251] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[   12.064072] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13
[   12.064355] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[   12.064601] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[   12.064848] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[   12.158375] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
--
[   26.077130] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[   31.161238] hda-intel: Invalid position buffer, using LPIB read method instead.
[   31.269629] hda-intel: Invalid position buffer, using LPIB read method instead.
[   31.296939] hda-intel: Invalid position buffer, using LPIB read method instead.
[   32.159940] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
[   32.267858] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[   34.734137] wlan0: no IPv6 routers present
--
[17414.913286] ehci_hcd 0000:00:1d.0: PCI INT A disabled
[17415.204932] snd_hda_intel 0000:00:1b.0: PCI INT A disabled
[17415.317829] snd_hda_intel 0000:01:00.1: PCI INT B disabled
[17415.317883] ACPI handle has no context!
--
[17416.126533] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
[17416.126557] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x103)
[17416.126569] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[17416.126573] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
[17416.126597] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x10010b)
--
[17416.126927] nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x800010, writing 0x800000)
[17416.126962] snd_hda_intel 0000:01:00.1: restoring config space at offset 0x1 (was 0x100006, writing 0x100002)
[17416.127008] xhci_hcd 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
--
[17416.127905] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[17416.127949] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[17416.127955] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[17416.127988] snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
[17416.128020] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
--
[17416.128056] ahci 0000:00:1f.2: setting latency timer to 64
[17416.128072] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[17416.128079] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[17416.128124] xhci_hcd 0000:02:00.0: setting latency timer to 64
--
[22590.768834] jmb38x_ms 0000:03:00.3: PCI INT B disabled
[22590.768930] snd_hda_intel 0000:01:00.1: PCI INT B disabled
[22590.768941] sdhci-pci 0000:03:00.1: PCI INT B disabled
--
[22590.779515] ehci_hcd 0000:00:1a.0: PCI INT A disabled
[22591.070773] snd_hda_intel 0000:00:1b.0: PCI INT A disabled
[22591.409020] PM: suspend of devices complete after 1206.070 msecs
--
[22592.164726] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
[22592.164749] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x103)
[22592.164762] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[22592.164766] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
[22592.164790] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x10010b)
--
[22592.165121] nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x800010, writing 0x800000)
[22592.165157] snd_hda_intel 0000:01:00.1: restoring config space at offset 0x1 (was 0x100006, writing 0x100002)
[22592.165202] xhci_hcd 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
--
[22592.166108] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[22592.166113] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[22592.166116] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[22592.166121] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[22592.166132] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[22592.166143] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[22592.166170] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[22592.166182] snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
[22592.166185] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[22592.166272] xhci_hcd 0000:02:00.0: setting latency timer to 64

upload=true&script=true&cardinfo=
!!################################
!!ALSA Information Script v 0.4.60
!!################################

!!Script ran on: Mon Jul 18 11:32:25 UTC 2011

!!Linux Distribution
!!------------------

Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock) Fedora release 15 (Lovelock)

!!DMI Information
!!---------------

Manufacturer:      CLEVO                            
Product Name:      P150HMx
Product Version:   Not Applicable                    

!!Kernel Information
!!------------------

Kernel release:    3.0-0.rc7.git3.1.belegdol.fc15.x86_64
Operating System:  GNU/Linux
Architecture:      x86_64
Processor:         x86_64
SMP Enabled:       Yes

!!ALSA Version
!!------------

Driver version:     1.0.24
Library version:    1.0.24
Utilities version:  1.0.24.1

!!Loaded ALSA modules
!!-------------------

snd_hda_intel
snd_hda_intel

!!Sound Servers on this system
!!----------------------------

Pulseaudio:
Installed - Yes (/usr/bin/pulseaudio)
Running - Yes

Jack:
Installed - Yes (/usr/bin/jackd)
Running - No

!!Soundcards recognised by ALSA
!!-----------------------------

0 [PCH ]: HDA-Intel - HDA Intel PCH

                      HDA Intel PCH at 0xf6500000 irq 52
 1 [NVidia         ]: HDA-Intel - HDA NVidia
                      HDA NVidia at 0xf6080000 irq 17

!!PCI Soundcards installed in the system
!!--------------------------------------

00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 01:00.1 Audio device: nVidia Corporation Device 0beb (rev a1)

!!Advanced information - PCI Vendor/Device/Subsystem ID's !!--------------------------------------------------------

00:1b.0 0403: 8086:1c20 (rev 05)

	Subsystem: 1558:5102
--
01:00.1 0403: 10de:0beb (rev a1)
	Subsystem: 1558:5102

!!Loaded sound module options
!!--------------------------

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!Module: snd_hda_intel

	bdl_pos_adj : 1,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	power_save : 0
	power_save_controller : Y
	probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : N

!!HDA-Intel Codec information
!!---------------------------
--startcollapse--

Codec: Realtek ALC892
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0892
Subsystem Id: 0x15585102
Revision Id: 0x100302
No Modem Function Group found
Default PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Speaker Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Device: name="ALC892 Analog", type="Audio", device=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Surround Playback Volume", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x37 0x37]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x05 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Center Playback Volume", index=0, device=0

    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Volume", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
  Amp-Out vals:  [0x27 0x27]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Control: name="IEC958 Default PCM Playback Switch", index=0, device=0
Device: name="ALC892 Digital", type="SPDIF", device=1
Converter: stream=5, channel=0
Digital: Enabled
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=0, device=0
Control: name="Capture Volume", index=0, device=0
Device: name="ALC892 Analog", type="Audio", device=0 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x1b 0x1b]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x23

Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Switch", index=1, device=0
Control: name="Capture Volume", index=1, device=0
Device: name="ALC892 Analog", type="Audio", device=2 Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1 Amp-In vals: [0x80 0x80]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x22

Node 0x0a [Audio Input] wcaps 0x100711: Stereo Digital
Converter: stream=0, channel=0
SDI-Select: 0
Digital:
Digital category: 0x0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x1f
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Internal Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Internal Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Line Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Control: name="Line Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
  Amp-In vals:  [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
  Connection: 10
     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17

Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00]
Connection: 2

     0x02 0x0b

Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00]
Connection: 2

     0x03 0x0b

Node 0x0e [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x04 0x0b

Node 0x0f [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x05 0x0b

Node 0x10 [Audio Output] wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x11 [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x10

Node 0x12 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0

    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x0001003e: IN OUT HP EAPD Detect Trigger
  EAPD 0x2: EAPD
  Pin Default 0x99130110: [Fixed] Speaker at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x0c

Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0d

Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0e

Node 0x17 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00]
Pincap 0x00000036: IN OUT Detect Trigger
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x0f
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Center Playback Switch", index=0, device=0
    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Switch", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Control: name="Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x01a11c30: [Jack] Mic at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0x0
  Pin-ctls: 0x40: OUT VREF_HIZ
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c 0x0d 0x0e 0x0f* 0x26
Node 0x19 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Internal Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x0000373e: IN OUT HP Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x99a30931: [Fixed] Mic at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x3, Sequence = 0x1
    Misc = NO_PRESENCE
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1a [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Surround Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x0181143f: [Jack] Line In at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0xf
  Pin-ctls: 0x40: OUT VREF_HIZ
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c 0x0d 0x0e* 0x0f 0x26
Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Headphone Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x0001373e: IN OUT HP EAPD Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  EAPD 0x2: EAPD
  Pin Default 0x0121101f: [Jack] HP Out at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x1, Sequence = 0xf
  Pin-ctls: 0xc0: OUT HP VREF_HIZ
  Unsolicited: tag=04, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c 0x0d* 0x0e 0x0f 0x26

Node 0x1c [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x00000024: IN Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1d [Pin Complex] wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x598301f0: [N/A] Line In at Int ATAPI
Conn = ATAPI, Color = Unknown DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x01451120: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = Black DefAssociation = 0x2, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1

     0x06

Node 0x1f [Pin Complex] wcaps 0x400681: Stereo Digital
Pincap 0x00000020: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=24
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=1, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 12

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b 0x12

Node 0x23 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Input Source", index=0, device=0
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 11

     0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b

Node 0x24 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x25 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0 Amp-Out vals: [0x40 0x40]
Converter: stream=0, channel=0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x26 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2

     0x25 0x0b

Codec: Nvidia GPU 12 HDMI/DP
Address: 0
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital: Enabled GenLevel
Digital category: 0x2
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 1
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=2, device=0
Control: name="IEC958 Playback Pro Mask", index=2, device=0
Control: name="IEC958 Playback Default", index=2, device=0
Control: name="IEC958 Playback Switch", index=2, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

Codec: Nvidia GPU 12 HDMI/DP
Address: 3
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x10de0012
Subsystem Id: 0x10de0101
Revision Id: 0x100100
No Modem Function Group found
Default PCM:

    rates [0x0]:
    bits [0x0]:
    formats [0x0]:

Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Audio Output] wcaps 0x72b1: 8-Channels Digital Stripe CP
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:

    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Unsolicited: tag=00, enabled=0
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
Control: name="IEC958 Playback Con Mask", index=3, device=0
Control: name="IEC958 Playback Pro Mask", index=3, device=0
Control: name="IEC958 Playback Default", index=3, device=0
Control: name="IEC958 Playback Switch", index=3, device=0 Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=05, enabled=1
Connection: 1

     0x04

--endcollapse--

!!ALSA Device nodes
!!-----------------

crw-rw----+ 1 root audio 116, 7 Jul 17 21:29 /dev/snd/controlC0 crw-rw----+ 1 root audio 116, 16 Jul 17 21:29 /dev/snd/controlC1 crw-rw----+ 1 root audio 116, 6 Jul 17 21:29 /dev/snd/hwC0D0 crw-rw----+ 1 root audio 116, 15 Jul 17 21:29 /dev/snd/hwC1D0 crw-rw----+ 1 root audio 116, 14 Jul 17 21:29 /dev/snd/hwC1D1 crw-rw----+ 1 root audio 116, 13 Jul 17 21:29 /dev/snd/hwC1D2 crw-rw----+ 1 root audio 116, 12 Jul 17 21:29 /dev/snd/hwC1D3

crw-rw----+ 1 root audio 116,  5 Jul 17 21:56 /dev/snd/pcmC0D0c
crw-rw----+ 1 root audio 116,  4 Jul 18 13:31 /dev/snd/pcmC0D0p
crw-rw----+ 1 root audio 116,  3 Jul 17 21:31 /dev/snd/pcmC0D1p
crw-rw----+ 1 root audio 116,  2 Jul 17 21:29 /dev/snd/pcmC0D2c
crw-rw----+ 1 root audio 116, 11 Jul 17 21:56 /dev/snd/pcmC1D3p
crw-rw----+ 1 root audio 116, 10 Jul 17 21:29 /dev/snd/pcmC1D7p
crw-rw----+ 1 root audio 116,  9 Jul 17 21:29 /dev/snd/pcmC1D8p
crw-rw----+ 1 root audio 116,  8 Jul 17 21:29 /dev/snd/pcmC1D9p
crw-rw----+ 1 root audio 116,  1 Jul 17 21:29 /dev/snd/seq

crw-rw----+ 1 root audio 116, 33 Jul 17 21:29 /dev/snd/timer

/dev/snd/by-path:
total 0
drwxr-xr-x. 2 root root 80 Jul 17 21:29 .
drwxr-xr-x. 3 root root 400 Jul 17 21:29 ..
lrwxrwxrwx. 1 root root 12 Jul 17 21:29 pci-0000:00:1b.0 -> ../controlC0 lrwxrwxrwx. 1 root root 12 Jul 17 21:29 pci-0000:01:00.1 -> ../controlC1

!!ALSA configuration files
!!------------------------

!!System wide config file (/etc/asound.conf)

#
# Place your global alsa-lib configuration here... #

@hooks [

	{
		func load
		files [
			"/etc/alsa/pulse-default.conf"
		]
		errors false
	}

]

!!Aplay/Arecord output
!!------------

APLAY

**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0

ARECORD

**** List of CAPTURE Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 2: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0

!!Amixer output
!!-------------

!!-------Mixer controls for card 0 [PCH]

Card hw:0 'PCH'/'HDA Intel PCH at 0xf6500000 irq 52'
Mixer name : 'Realtek ALC892'
Components : 'HDA:10ec0892,15585102,00100302'
Controls : 34
Simple ctrls : 20
Simple mixer control 'Master',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 55 [86%] [-9.00dB] [on]
Simple mixer control 'Headphone',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Speaker',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'PCM',0
Capabilities: pvolume penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 254 [100%] [0.20dB]
Front Right: Playback 254 [100%] [0.20dB]
Simple mixer control 'Surround',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Center',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 48 [75%] [-16.00dB] [on]
Simple mixer control 'LFE',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 48 [75%] [-16.00dB] [on]
Simple mixer control 'Line',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958 Default PCM',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 27 [59%] [11.00dB] [on]
Front Right: Capture 27 [59%] [11.00dB] [on]
Simple mixer control 'Capture',1
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 46
Front Left: Capture 0 [0%] [-16.00dB] [off]
Front Right: Capture 0 [0%] [-16.00dB] [off]
Simple mixer control 'Auto-Mute Mode',0
Capabilities: enum
Items: 'Disabled' 'Enabled'
Item0: 'Enabled'
Simple mixer control 'Channel Mode',0
Capabilities: enum
Items: '2ch' '4ch' '6ch'
Item0: '6ch'
Simple mixer control 'Input Source',0
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Mic'
Simple mixer control 'Input Source',1
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Line'
Item0: 'Mic'
Simple mixer control 'Internal Mic',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Internal Mic Boost',0
Capabilities: volume penum
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]

!!-------Mixer controls for card 1 [NVidia]

Card hw:1 'NVidia'/'HDA NVidia at 0xf6080000 irq 17'
Mixer name : 'Nvidia GPU 12 HDMI/DP'
Components : 'HDA:10de0012,10de0101,00100100'
Controls : 16
Simple ctrls : 4
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958',1
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',2
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',3
Capabilities: pswitch pswitch-joined penum Playback channels: Mono
Mono: Playback [off]

!!Alsactl output
!!-------------

--startcollapse--

state.PCH {
	control.1 {
		iface MIXER
		name 'Channel Mode'
		value '6ch'
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 '2ch'
			item.1 '4ch'
			item.2 '6ch'
		}
	}
	control.2 {
		iface MIXER
		name 'Headphone Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.3 {
		iface MIXER
		name 'Headphone Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.4 {
		iface MIXER
		name 'Surround Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.5 {
		iface MIXER
		name 'Surround Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.6 {
		iface MIXER
		name 'Center Playback Volume'
		value 48
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 -1600
		}
	}
	control.7 {
		iface MIXER
		name 'LFE Playback Volume'
		value 48
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 -1600
		}
	}
	control.8 {
		iface MIXER
		name 'Center Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'LFE Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'Speaker Playback Volume'
		value.0 64
		value.1 64
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.11 {
		iface MIXER
		name 'Speaker Playback Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.12 {
		iface MIXER
		name 'Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.13 {
		iface MIXER
		name 'Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.14 {
		iface MIXER
		name 'Internal Mic Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.15 {
		iface MIXER
		name 'Internal Mic Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.16 {
		iface MIXER
		name 'Line Playback Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 31'
			dbmin -3450
			dbmax 1200
			dbvalue.0 -3450
			dbvalue.1 -3450
		}
	}
	control.17 {
		iface MIXER
		name 'Line Playback Switch'
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.18 {
		iface MIXER
		name 'Auto-Mute Mode'
		value Enabled
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Disabled
			item.1 Enabled
		}
	}
	control.19 {
		iface MIXER
		name 'Mic Boost Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.20 {
		iface MIXER
		name 'Internal Mic Boost Volume'
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 3'
			dbmin 0
			dbmax 3000
			dbvalue.0 0
			dbvalue.1 0
		}
	}
	control.21 {
		iface MIXER
		name 'Capture Switch'
		value.0 true
		value.1 true
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.22 {
		iface MIXER
		name 'Capture Switch'
		index 1
		value.0 false
		value.1 false
		comment {
			access 'read write'
			type BOOLEAN
			count 2
		}
	}
	control.23 {
		iface MIXER
		name 'Capture Volume'
		value.0 27
		value.1 27
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 1100
			dbvalue.1 1100
		}
	}
	control.24 {
		iface MIXER
		name 'Capture Volume'
		index 1
		value.0 0
		value.1 0
		comment {
			access 'read write'
			type INTEGER
			count 2
			range '0 - 46'
			dbmin -1600
			dbmax 3000
			dbvalue.0 -1600
			dbvalue.1 -1600
		}
	}
	control.25 {
		iface MIXER
		name 'Input Source'
		value Mic
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.26 {
		iface MIXER
		name 'Input Source'
		index 1
		value Mic
		comment {
			access 'read write'
			type ENUMERATED
			count 1
			item.0 Mic
			item.1 'Internal Mic'
			item.2 Line
		}
	}
	control.27 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.28 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.29 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.30 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.31 {
		iface MIXER
		name 'IEC958 Default PCM Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.32 {
		iface MIXER
		name 'Master Playback Volume'
		value 55
		comment {
			access 'read write'
			type INTEGER
			count 1
			range '0 - 64'
			dbmin -6400
			dbmax 0
			dbvalue.0 -900
		}
	}
	control.33 {
		iface MIXER
		name 'Master Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.34 {
		iface MIXER
		name 'PCM Playback Volume'
		value.0 254
		value.1 254
		comment {
			access 'read write user'
			type INTEGER
			count 2
			range '0 - 255'
			tlv '0000000100000008ffffec1400000014'
			dbmin -5100
			dbmax 0
			dbvalue.0 -20
			dbvalue.1 -20
		}
	}
}
state.NVidia {
	control.1 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.2 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.3 {
		iface MIXER
		name 'IEC958 Playback Default'
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.4 {
		iface MIXER
		name 'IEC958 Playback Switch'
		value true
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.5 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 1
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.6 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 1
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.7 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 1
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.8 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 1
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.9 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 2
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.10 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 2
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.11 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 2
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.12 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 2
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
	control.13 {
		iface MIXER
		name 'IEC958 Playback Con Mask'
		index 3
		value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.14 {
		iface MIXER
		name 'IEC958 Playback Pro Mask'
		index 3
		value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access read
			type IEC958
			count 1
		}
	}
	control.15 {
		iface MIXER
		name 'IEC958 Playback Default'
		index 3
		value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
		comment {
			access 'read write'
			type IEC958
			count 1
		}
	}
	control.16 {
		iface MIXER
		name 'IEC958 Playback Switch'
		index 3
		value false
		comment {
			access 'read write'
			type BOOLEAN
			count 1
		}
	}
}

--endcollapse--

!!All Loaded Modules
!!------------------

Module
tcp_lp
ebtable_nat
ebtables
ipt_MASQUERADE
iptable_nat
nf_nat
xt_CHECKSUM
iptable_mangle
bridge
stp
llc
ppdev
parport_pc
lp
parport
sunrpc
bnep
bluetooth
nf_conntrack_ipv4
nf_defrag_ipv4
ip6t_REJECT
nf_conntrack_ipv6
nf_defrag_ipv6
xt_state
nf_conntrack
ip6table_filter
ip6_tables
nvidia
snd_hda_codec_hdmi
snd_hda_codec_realtek
fuse
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_seq
snd_seq_device
snd_pcm
snd_timer
snd
arc4
iwlagn
mac80211
uvcvideo
videodev
i2c_i801
soundcore
cfg80211
microcode
jmb38x_ms
xhci_hcd
joydev
media
v4l2_compat_ioctl32
snd_page_alloc
rfkill
jme
serio_raw
memstick
i2c_core
mii
iTCO_wdt
iTCO_vendor_support
binfmt_misc
virtio_net
kvm_intel
kvm
firewire_ohci
firewire_core
crc_itu_t
sdhci_pci
sdhci
mmc_core
wmi
video

!!Sysfs Files
!!-----------

/sys/class/sound/hwC0D0/init_pin_configs:
0x11 0x411111f0
0x12 0x411111f0
0x14 0x99130110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x411111f0
0x18 0x01a11c30
0x19 0x99a30931
0x1a 0x0181143f
0x1b 0x0121101f
0x1c 0x411111f0
0x1d 0x598301f0
0x1e 0x01451120
0x1f 0x411111f0

/sys/class/sound/hwC0D0/driver_pin_configs:

/sys/class/sound/hwC0D0/user_pin_configs:

/sys/class/sound/hwC0D0/init_verbs:

/sys/class/sound/hwC1D0/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D0/driver_pin_configs:

/sys/class/sound/hwC1D0/user_pin_configs:

/sys/class/sound/hwC1D0/init_verbs:

/sys/class/sound/hwC1D1/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D1/driver_pin_configs:

/sys/class/sound/hwC1D1/user_pin_configs:

/sys/class/sound/hwC1D1/init_verbs:

/sys/class/sound/hwC1D2/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D2/driver_pin_configs:

/sys/class/sound/hwC1D2/user_pin_configs:

/sys/class/sound/hwC1D2/init_verbs:

/sys/class/sound/hwC1D3/init_pin_configs:
0x05 0x18560010

/sys/class/sound/hwC1D3/driver_pin_configs:

/sys/class/sound/hwC1D3/user_pin_configs:

/sys/class/sound/hwC1D3/init_verbs:

!!ALSA/HDA dmesg
!!------------------

[   11.619432] Disabling lock debugging due to kernel taint
[   11.631239] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   11.631334] snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
[   11.631356] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[   11.635107] fuse init (API version 7.16)
[   11.641039] SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
[   11.691510] hda_codec: ALC892: SKU not ready 0x598301f0
[   11.691680] hda_codec: ALC892: BIOS auto-probing.
[   11.691690] ALSA sound/pci/hda/hda_codec.c:4878 autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   11.691695] ALSA sound/pci/hda/hda_codec.c:4882    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   11.691699] ALSA sound/pci/hda/hda_codec.c:4886    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   11.691703] ALSA sound/pci/hda/hda_codec.c:4887    mono: mono_out=0x0
[   11.691706] ALSA sound/pci/hda/hda_codec.c:4890    dig-out=0x1e/0x0
[   11.691709] ALSA sound/pci/hda/hda_codec.c:4891    inputs:
[   11.691714] ALSA sound/pci/hda/hda_codec.c:4895  Mic=0x18
[   11.691718] ALSA sound/pci/hda/hda_codec.c:4895  Internal Mic=0x19
[   11.691721] ALSA sound/pci/hda/hda_codec.c:4895  Line=0x1a
[   11.691724] ALSA sound/pci/hda/hda_codec.c:4897 
[   11.693727] ALSA sound/pci/hda/patch_realtek.c:1267 realtek: No valid SSID, checking pincfg 0x598301f0 for NID 0x1d
[   11.693732] ALSA sound/pci/hda/patch_realtek.c:1348 realtek: Enable default setup for auto mode as fallback
[   11.698816] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   11.699014] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   11.699018] hda_intel: Disabling MSI
[   11.699119] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[   11.705661] ALSA sound/pci/hda/hda_intel.c:1454 Enable delay in RIRB handling
[   11.848573] SELinux: initialized (dev sda2, type fuseblk), uses genfs_contexts
--
[   11.850026] ntfs-3g[887]: Ownership and permissions disabled, configuration type 1
[   11.924388] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.963381] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0
[   12.002301] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0
[   12.041251] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[   12.064072] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13
[   12.064355] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[   12.064601] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[   12.064848] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[   12.158375] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
--
[   26.077130] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[   31.161238] hda-intel: Invalid position buffer, using LPIB read method instead.
[   31.269629] hda-intel: Invalid position buffer, using LPIB read method instead.
[   31.296939] hda-intel: Invalid position buffer, using LPIB read method instead.
[   32.159940] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
[   32.267858] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[   34.734137] wlan0: no IPv6 routers present
--
[17414.913286] ehci_hcd 0000:00:1d.0: PCI INT A disabled
[17415.204932] snd_hda_intel 0000:00:1b.0: PCI INT A disabled
[17415.317829] snd_hda_intel 0000:01:00.1: PCI INT B disabled
[17415.317883] ACPI handle has no context!
--
[17416.126533] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
[17416.126557] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x103)
[17416.126569] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[17416.126573] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
[17416.126597] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x10010b)
--
[17416.126927] nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x800010, writing 0x800000)
[17416.126962] snd_hda_intel 0000:01:00.1: restoring config space at offset 0x1 (was 0x100006, writing 0x100002)
[17416.127008] xhci_hcd 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
--
[17416.127905] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[17416.127949] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[17416.127955] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[17416.127988] snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
[17416.128020] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
--
[17416.128056] ahci 0000:00:1f.2: setting latency timer to 64
[17416.128072] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[17416.128079] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[17416.128124] xhci_hcd 0000:02:00.0: setting latency timer to 64
--
[22590.768834] jmb38x_ms 0000:03:00.3: PCI INT B disabled
[22590.768930] snd_hda_intel 0000:01:00.1: PCI INT B disabled
[22590.768941] sdhci-pci 0000:03:00.1: PCI INT B disabled
--
[22590.779515] ehci_hcd 0000:00:1a.0: PCI INT A disabled
[22591.070773] snd_hda_intel 0000:00:1b.0: PCI INT A disabled
[22591.409020] PM: suspend of devices complete after 1206.070 msecs
--
[22592.164726] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
[22592.164749] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x103)
[22592.164762] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[22592.164766] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
[22592.164790] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x10010b)
--
[22592.165121] nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x800010, writing 0x800000)
[22592.165157] snd_hda_intel 0000:01:00.1: restoring config space at offset 0x1 (was 0x100006, writing 0x100002)
[22592.165202] xhci_hcd 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
--
[22592.166108] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[22592.166113] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[22592.166116] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[22592.166121] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[22592.166132] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[22592.166143] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[22592.166170] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[22592.166182] snd_hda_intel 0000:00:1b.0: irq 52 for MSI/MSI-X
[22592.166185] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[22592.166272] xhci_hcd 0000:02:00.0: setting latency timer to 64
#64 lore raw

At Mon, 18 Jul 2011 13:42:50 +0200,

Quoted 28 lines · Julian Sikorski

W dniu 18.07.2011 13:19, Takashi Iwai pisze:

Quoted 26 lines

At Mon, 18 Jul 2011 13:15:14 +0200,

Quoted 23 lines · Julian Sikorski

W dniu 18.07.2011 10:52, Takashi Iwai pisze:

Quoted 7 lines

And I can't reproduce your problem with the alsa-info.sh output above. Give more exact information what you did and what is the problem.

thanks,

Takashi

I'm sorry for the confusion - let me sum up the current situation. With the fixes you pushed to sound-2.6/master I was able to get 5.1 sound out of my laptop. The only missing bit was the 7.1 sound. And the last channel goes via a jack/optical spdif hybrid. The problem is that the BIOS does not announce that and as such alsa is unaware of the side surround channel.
Using Raymond's advice, I was able to make the sound come out of the last jack, by changing some values for pin 0x17 (described as sidesurr in the datasheet), diff is attached. I basically checked what was the difference in alsa-info.sh output when I was changing number of channels with alsamixer, and then did the same for pin 0x17.
Since, from what I understood, you wanted me to figure out which pin is connected to the last jack [1], I thought this information would be useful to fix BIOS shortcomings.

Quoted 5 lines
Quoted 2 lines

Yes, and note that you can set up the initial pin configurations dynamically via sysfs, too.

I tried, but without much success [2] - I came up with 0x01111xxx, but I do not have enough understanding on what to put as the last 3 numbers.

The last three numbers are pretty important, so check the HD-audio specification.

Quoted 5 lines

Moreover, I keep getting this upon trying to apply the new pin configuration:

# echo 0x17 0x011111f0 > user_pin_configs
# LANG=C pasuspender echo 1 > reconfig
echo: write error: Device or resource busy

You should log out, go to linux console, and kill all processes accessing the sound devices, then do reconfig.

Quoted 10 lines
Quoted 10 lines
Quoted 4 lines

Other problem is that the volume on that jack is controlled by center and lfe sliders (in alsamixer), which is probably caused by the fact that alsa is unaware of the 7.1 sound.

And this is not what I can't reproduce.

Quoted 2 lines

If more information is needed, please let me know what do you need in addition to alsa-info.sh output.

Quoted 8 lines
Quoted 4 lines

First off, double-check whether the CLFE mixer really changes the pin amp. At best, take alsa-info.sh output snapshot before and after changing the mixer state, and compare the files (better give both files in the mail).

Here you go. playing.txt is the state when sound comes out of the spdif/side pin, and the center-lfe-half-volume.txt is when the volume is reduced to 50 % afterwards.

Between playing.txt and cneter-lfe-half-volume.txt, I see no change regarding the pin 0x17. The only difference is the DAC volume of NID 0x05. What am I missing?

Takashi

#65 lore raw

W dniu 18.07.2011 14:16, Takashi Iwai pisze:

Quoted 30 lines

At Mon, 18 Jul 2011 13:42:50 +0200,

Quoted 28 lines · Julian Sikorski

W dniu 18.07.2011 13:19, Takashi Iwai pisze:

Quoted 26 lines

At Mon, 18 Jul 2011 13:15:14 +0200,

Quoted 23 lines · Julian Sikorski

W dniu 18.07.2011 10:52, Takashi Iwai pisze:

Quoted 7 lines

And I can't reproduce your problem with the alsa-info.sh output above. Give more exact information what you did and what is the problem.

thanks,

Takashi

I'm sorry for the confusion - let me sum up the current situation. With the fixes you pushed to sound-2.6/master I was able to get 5.1 sound out of my laptop. The only missing bit was the 7.1 sound. And the last channel goes via a jack/optical spdif hybrid. The problem is that the BIOS does not announce that and as such alsa is unaware of the side surround channel.
Using Raymond's advice, I was able to make the sound come out of the last jack, by changing some values for pin 0x17 (described as sidesurr in the datasheet), diff is attached. I basically checked what was the difference in alsa-info.sh output when I was changing number of channels with alsamixer, and then did the same for pin 0x17.
Since, from what I understood, you wanted me to figure out which pin is connected to the last jack [1], I thought this information would be useful to fix BIOS shortcomings.

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

Yes, and note that you can set up the initial pin configurations dynamically via sysfs, too.

I tried, but without much success [2] - I came up with 0x01111xxx, but I do not have enough understanding on what to put as the last 3 numbers.

The last three numbers are pretty important, so check the HD-audio specification.

The specification [3] says the last 3 are misc, default association and sequence. So what I have now:
- misc: not sure here, since 3 out of 4 bits are reserved. 4th one should be 0 though, since the port has jack sensing functionality.
- default association: 3, as the working jacks have that set to 3
- sequence: since the working lfe has it set to 0 (center/lfe) and f (surround), I guess any value in between should work.
I am not sure if my reasoning is right though.

Quoted 9 lines
Quoted 6 lines

Moreover, I keep getting this upon trying to apply the new pin configuration:

# echo 0x17 0x011111f0>  user_pin_configs
# LANG=C pasuspender echo 1>  reconfig
echo: write error: Device or resource busy

You should log out, go to linux console, and kill all processes accessing the sound devices, then do reconfig.

OK, I will try with 0x17 0x111103b or something like that.

Quoted 16 lines
Quoted 16 lines
Quoted 15 lines
Quoted 5 lines

Other problem is that the volume on that jack is controlled by center and lfe sliders (in alsamixer), which is probably caused by the fact that alsa is unaware of the 7.1 sound.

And this is not what I can't reproduce.

Quoted 2 lines

If more information is needed, please let me know what do you need in addition to alsa-info.sh output.

First off, double-check whether the CLFE mixer really changes the pin amp. At best, take alsa-info.sh output snapshot before and after changing the mixer state, and compare the files (better give both files in the mail).

Quoted 7 lines
Quoted 3 lines

Here you go. playing.txt is the state when sound comes out of the spdif/side pin, and the center-lfe-half-volume.txt is when the volume is reduced to 50 % afterwards.

Between playing.txt and cneter-lfe-half-volume.txt, I see no change regarding the pin 0x17. The only difference is the DAC volume of NID 0x05. What am I missing?

Nothing probably. I can only confirm that the volume on the spdif/side jack goes down if you move the slider. I will check what does windows do.

Quoted 1 line

Takashi

Julian

[3]
http://www.intel.com/standards/hdaudio/pdf/High_Definition_Audio_1_0a.pdf

#66 lore raw

At Mon, 18 Jul 2011 14:42:55 +0200,

Quoted 7 lines · Julian Sikorski
Quoted 6 lines
Quoted 3 lines

I tried, but without much success [2] - I came up with 0x01111xxx, but I do not have enough understanding on what to put as the last 3 numbers.

The last three numbers are pretty important, so check the HD-audio specification.

Quoted 8 lines

The specification [3] says the last 3 are misc, default association and sequence. So what I have now:
- misc: not sure here, since 3 out of 4 bits are reserved. 4th one should be 0 though, since the port has jack sensing functionality.
- default association: 3, as the working jacks have that set to 3
- sequence: since the working lfe has it set to 0 (center/lfe) and f (surround), I guess any value in between should work.
I am not sure if my reasoning is right though.

The sequence number is the point. The driver assumes that the pins are ordered as front/CLFE/rear/side.

But, currently the multi-io assignment doesn't check the sequence number (because that number refers to the sequence of input pins). The extra channels are assigned in the order of widget NIDs (first from line-in pins, then mic-in pins). Its logic assumes that there are at most two valid input-pins.

That being said, you'd need to modify the driver anyway to make it working properly as I mentioned early in this thread, if a certain channel-map is required.

Takashi

#67 lore raw

W dniu 2011-07-18 15:23, Takashi Iwai pisze:

Quoted 27 lines

At Mon, 18 Jul 2011 14:42:55 +0200,

Quoted 7 lines · Julian Sikorski
Quoted 6 lines
Quoted 3 lines

I tried, but without much success [2] - I came up with 0x01111xxx, but I do not have enough understanding on what to put as the last 3 numbers.

The last three numbers are pretty important, so check the HD-audio specification.

Quoted 8 lines

The specification [3] says the last 3 are misc, default association and sequence. So what I have now:
- misc: not sure here, since 3 out of 4 bits are reserved. 4th one should be 0 though, since the port has jack sensing functionality.
- default association: 3, as the working jacks have that set to 3
- sequence: since the working lfe has it set to 0 (center/lfe) and f (surround), I guess any value in between should work.
I am not sure if my reasoning is right though.

The sequence number is the point. The driver assumes that the pins are ordered as front/CLFE/rear/side.

But, currently the multi-io assignment doesn't check the sequence number (because that number refers to the sequence of input pins). The extra channels are assigned in the order of widget NIDs (first from line-in pins, then mic-in pins). Its logic assumes that there are at most two valid input-pins.

Quoted 6 lines

That being said, you'd need to modify the driver anyway to make it working properly as I mentioned early in this thread, if a certain channel-map is required.

Takashi

I see. I am afraid there is not much more I can do then - I am a biologist and writing driver code is far beyond my IT skills. In the meantime, I was able to run reconfig in runlevel 3, but assigning
neither 0x0111103e nor 0x011111f0 to 0x17 produced any changes in
alsamixer output (which is expected in the light of what you wrote about modifying the driver).
When it comes to volume control issue, under windows it is possible to control center, lfe and side channels separately.

Julian